Bedienungsanleitung Bresser 70-20000 Connect Set (Seite 17 von 72) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

632904

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

Note: Please refer to “Router compatibility” and “Troubleshooting” sections if you encounter any problem when setting up

the gateway.

Wind meter (Fig. 3, 2)

• 1. Registration and setup

1) Align and connect the wind speed cups and wind vane to the wind meter and tighten the screws.

2) Place the wind meter next to the gateway.

3) Enable your WiFi reception on your iOS / Android device and run the “ BRESSER Connect” app .

4) Select “Weather” and then tap the “ i ” on the upper right corner to enter the setting display.

5) Tap “Wind, Temperature, Humidity”.

6) Tap ”+” on the upper right to add a new wind meter.

7) Open the battery door of the wind meter.

8) Use the compass on the wind meter and turn the wind vane so it is pointing due north (Fig. 4).

9) Hold the wind vane pointing due north and do not allow it to turn. Insert 2 pieces of AA batteries according to the

polarity indicated. The red LED indicator above the battery cover of the wind meter will ﬂash few times right after battery

installation. Be sure the vane is pointing due north at the moment when red LED ﬂashes and the calibration is now

completed.

10) If the wind vane is not pointing due north when the red LED ﬁrst ﬂashes, remove batteries and repeat step 8 and 9.

11) Tap “Connect” on the app within 30 seconds of battery installation to search for the wind meter.

12) Once connected, “Sensor is connected” appears and you have successfully registered your wind meter. You may

proceed to change the name and photo. Tap the “Save” icon on the upper right corner anytime to save and exit.

Replace the battery cover and tighten the screws on the wind meter

13) Return to the “Weather” main display and the wind speed/ direction, temperature and humidity readings will appear

within a short period.

• 2. Testing the effective transmission range

It is recommended to perform a simple transmission test before mounting the wind meter so as to ensure it is within the ef-

fective transmission range.

1) Select a mounting location for the wind meter that is:

- outdoors, not blocked on top or sides, so wind can freely reach the wind meter

- within 100 meter (328 feet) open area from the gateway. The distance is reduced when obstacles are between

the wind meter and the gateway

- Place the wind meter 1 meter above ground to simulate the minimum height after mounting

2) If there is wind when testing, let the wind meter run freely and follow the steps below:

- Run the app and go to the “Weather” page (make sure your WiFi is enabled on your iOS / Android device and

you are within the WiFi coverage area)

- If wind speed/direction readings continue to change and update every few minutes, your wind meter is within the

effective transmission range. Go to below section for mounting your wind meter.

3) If there is no wind when testing, wait for 25 minutes and follow below steps:

- Run the app and goes to the “Weather” page (make sure your WiFi is enabled on your iOS / Android device and

you are within the WiFi coverage area)

- If wind speed/direction reading still appears on the screen, your wind meter is within the effective transmission

range. Go to below section for mounting your wind meter

- If “---“ appears on the wind speed/direction page or “sensor is not connected” appears on its setting page, the

wind meter is out of the range.

Shorten the distance between the wind meter and the gateway. Go to the wind meter setting page and tap [Connect]

again to reconnect the sensor. Repeat this procedure until the sensor is connected.

Note: If you have run the Connect system for a long period of time, and one day your wind meter fails to connect with the

system while the rest of the sensors work ﬁne, it’s likely that the battery level in the wind meter is low. Please reinstall new

batteries and follow the setup procedure in the manual to reconnect with your Connect system.

Garantie

Warranty

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bresser 70-20000 Connect Set Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info