Bedienungsanleitung Bresser 70-20000 Connect Set (Seite 19 von 72) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

632904

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

• If rainfall readings still appear on the screen, your rain gauge is within the effective transmission range. Go to below sec-

tion for mounting your rain gauge.

• If “---“ appears on the rainfall reading area or “sensor is not connected” appears on its setting page, your rain gauge is

out of the range. Shorten the distance between the rain gauge & gateway. Go to the rain gauge settings page and tap

[Connect] again to reconnect the sensor. Repeat this procedure until the sensor is connected.

NOTE: If you have run the BRESSER Connect system for a long period of time, and one day your rain gauge fails to con-

nect with the system while the rest of the sensors work ﬁne, it’s likely that the battery level in the rain gauge is low. Please

reinstall new batteries and follow the setup procedure in the manual to reconnect with your BRESSER Connect system.

• 3. Mounting the rain gauge

Before mounting the rain gauge, be sure the rain gauge & monitor are within the effective transmission range and that batteries

are installed.

1) Hold the base of the rain gauge ﬂat against the mounting surface then use a level to make sure the rain gauge

(as it resst on the mounting surface) is horizontally level.

2) Use a pencil to trace the inside of the mounting holes on the base of the rain gauge to mark the screw locations.

3) Drill a hole in the center of each marked location and insert the supplied plastic screw plugs

Hold the rain gauge against the mounting surface so the holes on the base are aligned with the plugs, then thread

the supplied washer head screws into each hole and use a screwdriver to tighten them.

Thermo-hygrometer (Fig. 3, 3)

• 1. Registration and setup

1) Place the thermo-hygrometer next to the gateway

2) Enable your WiFi reception on your iOS / Android device and run the “BRESSER Connect” app

3) Select “Weather” and then tap the “ i ” on the upper right corner to enter the setting display

4) Tap “Temperature, Humidity”

5) Tap ”+” on the upper right to add a new thermo-hygrometer

6) Open the battery door on the thermo-hygrometer

7) Tap “Connect” on the app to search for the thermo-hygrometer

8) Insert 2 pieces of AAA batteries according to the polarity within 30 seconds after tapping the “Connect”.

9) Once the connection is established, “Sensor is connected” appears and you have successfully registered your sensor.

You may proceed to change the name & photo. Tap the “Save” icon on the upper right corner anytime to save and exit.

Close the battery door of the sensor

10) Return to the “Weather” main display and the temperature & humidity reading will appear after a short time

• 2. Testing the effective transmission range & setup

1) Select a location that is within the effective transmission range (100meters open area) and place the

hermo-hygrometer there. Reduce distance if obstacles are between the thermo-hygrometer & the gateway.

2) The thermo-hygrometer should be placed 1 meter above ground and avoid direct sunlight.

3) Wait for 25 minutes and follow below steps:

- Run the app and go to the “Weather” page (make sure your WiFi is enabled on your iOS / Android device and

you are within the WiFi coverage area)

- If temperature and humidity readings of the thermo-hygrometer still appear on the screen, your sensor is within the

effective transmission range and the sensor can be mounted.

- If “---“ appears on the thermo-hygrometer page or “sensor is not connected” appears on its setting page, your t

hermo-hygrometer is out of the range. Shorten the distance between the sensor and the gateway. Go to the

“temperature & humidity” setting page and tap [Connect] again to reconnect the sensor. Repeat this procedure until

the sensor is connected

NOTE: If you have run the BRESSER Connect system for a long period of time, and one day your thermo-hygrometer fails

to connect with the system while the rest of the sensors work ﬁne, it’s likely that the battery level in the thermo-hygrometer is

low. Please check the sensor and if the low battery icon appears on the LCD display, please reinstall new batteries and follow

the setup procedure in the manual to reconnect with your BRESSER Connect system.

Garantie

Warranty

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bresser 70-20000 Connect Set Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info