Bedienungsanleitung Bresser 7002540 PROFI W-LAN WETTER CENTER (Seite 15 von 20) (Deutsch, Englisch)

729972

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

4. To disable the alarm, press ALARM button until the alarm icons dis-

appear.

Fig. 21

Alarm off Alarm on Alarm and ice-alert on

NOTE!

1. Press ALARM/SNOOZE button when alarm sounds to interrupt the

alarm. The alarm will then start again after 5 minutes.

2. Pres ALARM button when alarm sounds to deactivate the alarm until

next time.

Alarm time setting

1. Press and hold ALARM button for 2 seconds to enter alarm setting

mode. Hours will begin to ash.

2. Use

or button to adjust the desired value and press ALARM

button to proceed to set minutes.

3. Repeat step 2 to set minutes, then press ALARM button to exit.

NOTE!

Press ALARM button twice when alarm time is being displayed will ac-

tivate the temperature-adjusted pre-alarm (ice-alert). The alarm will

sound 30 minutes earlier if it detects outside temperature is below -3°C.

WEATHER FORECAST

The device contains sensitive pressure sensor built-in with sophisticated

and proven software that predicts weather for the next 12 hours.

sunny, clear slightly cloudy cloudy rainy rainy, stormy snowy

Fig. 22

NOTE!

1. The accuracy of a general pressure-based weather forecast is about

70% to 75%.

2. The weather forecast is meant for the next 12 hours, it may not neces-

sarily reect the current situation.

3. The “Snowy” weather forecast is not based on the atmospheric pres-

sure, but based on the outdoor temperature. When the outdoor tem-

perature is below -3°C (26°F), the “Snowy” weather indicator will be

displayed on the LCD.

BAROMETRIC / ATMOSPHERIC PRESSURE

Atmospheric Pressure is the pressure at any location of the Earth caused

by the weight of the column of air above it. One atmospheric pressure re-

fers to the average pressure and gradually decreases as altitude increas-

es. Meteorologists use barometers to measure atmospheric pressure.

Since variation in atmospheric pressure greatly affected by weather, it is

possible to forecast the weather by measuring the changes in pressure.

Select display mode

1. Press and hold BARO button for 2 seconds to enter atmospheric pres-

sure setting mode.

2. Use

or button to select between absolute and relative atmos-

pheric pressure:

• ABSOLUTE the absolute atmospheric pressure of your location

• RELATIVE the relative atmospheric pressure based on the sea level

Set relative atmospheric pressure value

1. Get the atmospheric pressure data of the sea level (it is also the rel-

ative atmospheric pressure data of your home area) through the local

weather service, internet and other channels.

2. Press and hold BARO button for 2 seconds until ABSOLUTE or RELA-

TIVE ashes.

3. Press

or button to switch to RELATIVE mode.

4. Press BARO button again and the number for RELATIVE ashes.

5. Use

or button to change the value.

6. Press BARO button to save and exit the setting mode.

NOTE!

1. The default relative atmospheric pressure value is 1013 mb/hPa (29.91

inHg), which refers to the average atmospheric pressure.

2. When you change the relative atmospheric pressure value, the weather

indicators will change along with it.

3. The built-in barometer can notice the environmental absolute atmos-

pheric pressure changes. Based on the data collected, it can predict

the weather conditions in the forthcoming 12 hours. Therefore, the

weather indicators will change according to the detected absolute at-

mospheric pressure after you operate the clock for 1 hour.

4. The relative atmospheric pressure is based on the sea level, but it will

change with the absolute atmospheric pressure changes after operat-

ing the clock for 1 hour.

Select barometer measurement unit

Press BARO button several times until the desired measurement unit is

displayed: inHg, mmHg or hPa.

TEMPERATURE & HUMIDITY

Comfort Indication

The comfort indication is a pictorial indication based on indoor air tem-

perature and humidity in an attempt to determine comfort level.

Fig. 23

too cold comfortable too hot

NOTE!

1. Comfort indication can vary under the same temperature, depending

on the humidity.

2. There is no comfort Indication when temperature is below 0°C (32°F)

or over 60°C (140°F).

Temperature Trend

The temperature trend indicator shows the trends of changes in the forth-

coming few minutes. Arrows indicate a rising, steady or falling trend.

Rising Steady Falling

NOTE!

1. When the temperature is below -40°C, the LCD will display "Lo". If tem-

perature is above 80°C, the LCD will show "HI".

2. When humidity is below 1%, LCD will display "Lo". If humidity is above

99%, LCD will display "HI".

RAINFALL

Select display mode

The device displays how many mm / inches of rain are accumulated in a

one hour time period, based on current rainfall rate.

Press RAINFALL button several times until the disered time range is dis-

played:

• DAILY: Total rainfall from midnight

• HOURLY: Current rainfall rate in past an hour

• WEEKLY: Total rainfall from the current week

• MONTHLY: Total rainfall from the current calendar month

• Accumulate: the total rainfall since the last reset

Daily rainfall Hourly rainfall Weekly rainfall Monthly rainfall

Fig. 24

NOTE!

Rain rate is updated every 6 minutes, at every hour on the hour, and at 6,

12, 18, 24, 30, 36, 42, 48, 54 minute past the hour.

Select rainfall measurement unit

1. Press and hold RAINFALL button for 2 seconds to enter settings mode.

2. Use

or button to select mm (millimeter) or in (inch).

3. Press RAINFALL button again to conrm and exit.

Bresser 7002540 PROFI W-LAN WETTER CENTER Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bresser 7002540 PROFI W-LAN WETTER CENTER

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info