Bedienungsanleitung Bresser 7006300 - Tuya Smart (Seite 15 von 88) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

784615

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

ACTIVATING ALARM FUNCTION

1. In normal mode, press [ MODE / ALARM ] key to show the

alarm time for 5 seconds.

2. When the alarm time displays, press [ MODE / ALARM ] key

again to activate the alarm function. Alarm o󰀨 Alarm on

When clock reach the alarm time, alarm sound will start.

Where it can be stopped by following operation:

- Auto-stop after 2 minutes alarming if without any operation and the alarm will activate again in the next

day.

- By pressing [ALARM / SNOOZE] key to enter snooze that the alarm will sound again after 5 minutes.

- By pressing and hold [ALARM / SNOOZE] key for 2 seconds to stop the alarm and will activate again

in the next day

- By pressing [ MODE / ALARM ] key to stop the alarm and the alarm will activate again in the next

day.

NOTE:

- The snooze could be used continuously in 24 hours.

- During the snooze, the alarm icon “ ” will keep ashing.

WIRELESS SENSOR SIGNAL RECEIVING

1. The console display signal strength for the wireless sensor(s), as per table below:

Signal strength of wireless

sensor channel

No signal Weak signal Good signal

2. If the signal has discontinued and does not recover within 15 minutes, the signal icon will

disappear. The temperature and humidity will display “Er” for the corresponding channel.

3. If the signal does not recover within 48 hours, the “Er” display will become permanent. You

need to replace the batteries and then press [ SENSOR / WI-FI] key to pair up the sensor

again.

VIEW THE OTHER CHANNELS (OPTIONAL FEATURE WITH ADD ON EXTRA SENSORS)

This console is capable to pair with 7 wireless sensors. If you have 2 or more wireless sensors,

you can press [ CHANNEL ] key to switch between di󰀨erent wireless channels in normal mode,

or press and hold [ CHANNEL ] key for 2 seconds to toggle auto-cycle mode to display the

connected channels at 4 seconds interval.

During auto-cycle mode, the icon will show on the wireless sensor channels section of the

console's display. Press [ CHANNEL ] key to stop auto cycle and display the current channel.

TEMPERATURE / HUMIDITY FUNCTION

- The temperature and humidity reading are display on the Channel and indoor section.

- Use the [ °C / °F ] key to select the temperature display unit.

- If temperature / humidity is below the measurement range, the reading will show “LO”. If temperature /

humidity is above the measurement range, the reading will show “HI”.

COMFORT INDICATION

The comfort indication is a pictorial indication

based on indoor air temperature and humidity in

an attempt to determine comfort level. Too cold Comfortable Too hot

NOTE:

- Comfort indication can vary under the same temperature, depending on the humidity.

- There is no comfort indication when temperature is below 0°C (32°F) or over 60°C (140°F).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bresser 7006300 - Tuya Smart Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info