Bedienungsanleitung Bresser 7060100 MyTime Crystal P Colour (Seite 8 von 16) (Englisch)

729964

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

8 / 16

1 Current time (hours) 2 Current time (minutes)

3 Snooze function enabled 4 Alarm enabled

5 Battery level (base station) 6 Current time (seconds)

7 Indoor temperature 8 Relative humidity (indoor) in %

9 Temperature trend (indoor) (rising, steady

or falling)

10 Relative humidity (outdoor) in %

11 Selected channel for remote sensor 12 Temperature unit (°C or °F selectable)

13 Outdoor temperature 14 Battery level (remote sensor)

15 Temperature trend (outdoor) 16 Weekday

17 Month 18 Day

19 Alarm time (minutes) 20 Symbol for alarm time setting

21 Highest or lowest value for indoor temper-

ature (depending on 18)

22 Highest or lowest value for indoor humidity

(depending on 23)

23 Symbol for highest (MAX) or lowest (MIN)

value (indoor)

24 Highest or lowest value for outdoor humid-

ity (depending on 25)

25 Symbol for highest (MAX) or lowest (MIN)

value (outdoor)

26 Highest or lowest value for outdoor tem-

perature (depending on 25)

27 Symbol for channel rotation 28 Year

29 Alarm time (hours)

8 Before starting operation

NOTICE

Avoid connectivity disruptions!

To avoid connectivity disruptions between the devices, consider the following points before starting

operation.

1. Place base station (receiver) and remote sensor (sender) together as close as possible.

2. Set up power supply for the base station and wait until the indoor temperature is displayed.

3. Set up power supply for the remote sensor.

4. Position the base station and the remote sensor within the effective transmission range.

5. Ensure that the base station and remote sensor are assigned to the same channel.

When changing batteries always change batteries in the main unit as well as all remote units and re-

place them in the correct order, so the remote connection can be re-established. If either of the

devices is mains-powered, the power supply must be disconnected for a short moment also for this

device when exchanging the batteries. If batteries are exchanged in only one of the devices (i.e. the

remote sensor) the signal can’t be received or can’t be received correctly.

Note, that the effective range is vastly affected by building materials and position of the main and re-

mote units. Due to external influences (various RC devices and other sources of interference), the

maximum distance can be greatly reduced. In such cases we suggest to position the main unit and the

remote sensor at other places. Sometimes all it takes is a relocation of one of these components of a

few inches! Though the remote unit is weather proof, it should be placed away from direct sunlight,

rain or snow.

9 Setting up power supply

Base station

1. Put the DC connector into the connection socket of the base station.

2. Put the mains plug into the power outlet.

3. The device is energized directly.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bresser 7060100 MyTime Crystal P Colour Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bresser 7060100 MyTime Crystal P Colour

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info