Bedienungsanleitung Bresser 7060100 MyTime Crystal P Colour (Seite 9 von 16) (Englisch)

729964

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

9 / 16

4. Wait until the indoor temperature is displayed on the base station.

NOTICE!For permanent operation, mains power supply is recommended. Alternatively a

power supply with batteries is also possible. Proceed as follows:

5. Remove the battery compartment cover.

6. Insert the batteries into the battery compartment. Ensure that the battery polarity (+/-) is correct.

7. Replace the battery compartment cover.

8. Wait until the indoor temperature is displayed on the base station.

NOTICE!When switching from mains power supply to battery power supply or vice versa,

the power supply is being disabled for a short moment for technical reasons. In this process

all settings made previously, will be deleted.

Remote sensor

1. Loosen the screws at the battery compartment cover with a small Philips screwdriver and remove

the cover.

NOTICE!Make sure not to lose the thin silicone sealing frame when removing the battery

compartment cover. It is an important protection against water infiltration and often ad-

heres at the battery compartment cover.

2. Insert the batteries into the battery compartment. Ensure that the battery polarity (+/-) is correct.

3. Set the channel selector switch to the desired channel (1, 2 or 3).

NOTICE!This weather station can be operated with up to 3 remote sensors. Each remote

sensor being connected must be operated on a different channel. If only one remote sensor

is connected, it should be operated on channel 1. Always press TX button after changing the

channel.

4. Press RESET button. The function indicator lights up for a short moment.

5. Put the sealing frame back onto the edge of the battery compartment.

6. Replace the cover and retighten it with the screws.

10 Manual time setting

1. Press and hold SET button for approx. 2 seconds to change to time setting mode.

2. Digits to be set are flashing.

3. Press UP or DOWN button to change the value.

4. Press SET button to confirm and continue to the next setting.

5. Settings order: Hours > Minutes > Change day/month display > Language > Year > Month >

12/24-hours mode

6. Finally press the SET button to save the settings and exit the setting mode.

11 Alarm setting

1. Press MODE button to switch to alarm time display.

2. Press and hold ALARM button for approx. 2 seconds to enter the alarm time setting mode (AL).

3. Digits to be set are flashing.

4. Press UP or DOWN button to change the value.

5. Press ALARM button to confirm and continue to the next setting.

6. Settings order: Hours > Minutes

7. Finally press the ALARM button to save the settings and exit the setting mode. Alarm will be activ-

ated automatically. The symbol will be displayed.

8. Press MODE button in normal display mode to display the alarm time.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bresser 7060100 MyTime Crystal P Colour Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bresser 7060100 MyTime Crystal P Colour

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info