Bedienungsanleitung Bresser 7902510 Weather Center 5-in-1 (Seite 15 von 20) (Deutsch, Englisch, Französisch, Italienisch, Spanisch)

771276

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

HISTORY DATA

(all records in the past 24 hours)

The main unit automatically records and displays data of the past 24

hours on the hour.

To check all the history data in the past 24 hours, press the HISTORY

button.

E.g. current time 7:25 a.m., Mach 28:

Press HISTORY button repeatedly to view past readings at 7:00am,

6:00am, 5:00am, …, 5:00am (Mar 27), 6:00am (Mar 27), 7:00am (Mar 27)

The LCD will display the past indoor and outdoor temperature & humidity,

value of air pressure, wind chill, wind speed, rainfall and their time and

date.

MAXIMUM / MINIMUM MEMORY FUNCTION

1. Press MAX/MIN button to check the maximum/minimum records.

The checking orders will be: Outdoor max temperature > Outdoor min

temperature > Outdoor max humidity > Outdoor min humidity > Indoor

max temperature > Indoor min temperature > Indoor max humidity

> Indoor min humidity > Outdoor max wind chill > Outdoor min wind

chill > Outdoor max heat index > Outdoor min heat index > Indoor max

dewpoint > Indoor min dewpoint > Max pressure > Min pressure > Max

average > Max gust > Max rainfall.

2. Press and hold MAX/MIN button for 2 seconds to reset the maximum

and minimum records.

NOTE!

When maximum or minimum reading is displayed, the corresponding

timestamp will be shown.

HI / LO ALERT

HI/LO alert are used to alert you of certain weather conditions. Once

activated, the alarm will turn on and amber LED starts flashing when a

certain criterion is met. The following are areas and type of alert provided:

Bereich Verfügbarer Alarm-

Typ

Indoor temperature HI AL / LO AL

Indoor humidity HI AL / LO AL

Outdoor temperaturw HI AL / LO AL

Outdoor humidity HI AL / LO AL

Rainfall HI AL*

Wind speed HI AL

*Daily rainfall since midnight

HI / LO alert setting (Fig. 29)

1. Press button several times until the desired area is selected.

2. Use or buttons to adjust the setting.

3. Press button to confirm and continue to next setting.

Fig. 29

Enable/Disable HI / LO alert (Fig. 30)

1. Press button several times until the desired area is selected..

2. Press button to turn the alert on or off.

3. Press button again to confirm and continue to next setting.

Fig. 30

NOTE!

1. The unit will automatically exit setting mode in 5 seconds if no

button is pressed.

2. When ALERT alarm is on, the area and type of alarm that triggered the

alarm will be flashing and the alarm will sound for 2 minutes.

3. Press SNOOZE/LIGHT button when alarm sounds to interrupt the

alarm. The alarm will then start again after 5 minutes.

4. Press button when alarm sounds to deactivate the alarm until

next time.

The alarm automatically turns off after 2 minutes.

WIRELESS SIGNAL RECEPTION

Fig. 31

No sensor Signal searching Strong signal Weak signal Signal lost

The 5-in-1 sensor is capable of transmitting data wirelessly over an

approximate operating of 150m range (line of sight).

Occasionally, due to intermittent physical obstructions or other

environmental interference, the signal may be weaken or lost.

In the case that the sensor signal is lost completely, you will need to

relocate the main unit or the wireless 5-in-1 sensor.

POINTING 5-IN-1 SENSOR TO THE SOUTH

The outdoor 5-in-1 sensor is calibrated to be pointing to North by

default. However, in some cases, users may wish to install the product

with the arrow pointing towards the South, especially for people living

in the Southern hemisphere (e.g. Australia, New Zealand).

1. First install the outdoor 5-in-1 sensor with its arrow pointing to the

South. (Please refer to 'Installation' chapter for mounting details)

2. Press and hold button for 8 seconds until the upper part (Northern

hemisphere) of the compass rose is blinking.

3. Use or button to change to lower part (Southern hemisphere).

Fig. 32

Northern hemisphere Southern hemisphere

4. Press button again to confirm and exit.

NOTE!

Changing from hemisphere setting will automatically switch the

direction of the moon phase on the display.

MOON PHASES

In the Northern hemisphere, the moon waxes (the part of the moon we

see that glows after the New Moon) from the right. Hence the sun-lit

area of the moon moves from right to left in the Northern hemisphere,

while in the Southern hemisphere, it moves from left to right. Below are

the 2 tables which illustrate how the moon will appear on the main unit.

Northern hemisphere:

New moon Full moon

Waxing crescent Waning gibbous

First quarter Third quarter

Waxing gibbous Waning crescent

Southern hemisphere:

New moon Full moon

Waxing crescent Waning gibbous

First quarter Third quarter

Waxing gibbous Waning crescent

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bresser 7902510 Weather Center 5-in-1 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Bresser 7902510 Weather Center 5-in-1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info