Bedienungsanleitung Bresser Digital Microscope (Seite 21 von 74) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

480805

Zoom out

Zoom in

Vorherige Seite

1/74

Nächste Seite

vation with a microscope. Set one of these

permanent slide preparations onto the micro-

scope stage (7). Push the slide underneath

both slide clips on the microscope stage, so

that nothing can move about during the obser-

vation. Then, turn the light to substage illumina-

tion (8) by pressing the On/Off button for the

light (16) as described in section 3.1. In the

next step, adjust the permanent slide so that

the observation object is clearly visible on the

monitor, in the preview area of the camera soft-

ware. Now, slowly turn the focus adjustment

knob (11) left or right until the image depicted

is in focus. By pushing multiple times on the

buttons for light brightness (+/-) (15), you can

set the illumination such that the ne details of

the observation object appear clearly on the

monitor as well.

If you would like to switch to a higher magni-

cation, turn the magnication adjustment knob

(3) to the left, to the position “80x” or “350x”.

Important:

Each time you adjust the magnication, you

must also use the magnication adjustment

knob (3) to change the focus.

3.5.1 Observing Opaque Objects

If you would like to observe opaque objects

with this microscope, the object must be lit

from above. Therefore, use the On/Off but-

ton for the illumination (16) to set the lighting

to surface illumination (5), as described in

section 3.1. Place the observation object on

the small, round disk in the middle of the mi-

croscope stage. Using the focus adjustment

knob (11), focus the image. It will also then

appear in focus on the monitor. You might

have to move the observation object around

a little bit so that it is displayed properly on

the monitor. By pushing multiple times on the

buttons for light brightness (+/-) (15), you can

set the illumination such that the ne details of

the observation object appear clearly on the

monitor as well.

The Digital Microscope allows you to observe

objects with a height of up to 6 mm.

Tip:

If you are observing objects that are only

slightly transparent (e.g. minerals, grains of

sand, etc.), you can improve the picture qual-

ity by using surface and substage illumination

at the same time (section 3.1.). Illumination

from both directions is achieved with the On/

Off button for the light (+/-) (15).

Important:

If you turn on the illumination on the micro-

scope in a very bright room or near a window

on a sunny day, the image on the monitor can

appear much too bright. This is because the

camera is very sensitive. Too much light thus

overpowers the ne details of the observation

object. In this case, you must completely shut

off the light on the Digital Microscope, so that

all the details will become visible again on the

monitor.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bresser Digital Microscope Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info