Bedienungsanleitung Bresser LED - LG-Serie (Seite 12 von 16) (Deutsch, Englisch)

771777

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

2. Turn on the device with the On/Off switch (Fig. 2, D) for 12V

DC power supply.

1.3. V-Lock Li-Ionen battery (optional)

NOTE!

The manufacturer is not liable for voltage damage due to the

use of an improper accumulator.

1. Push the battery5 into the V-Lock holder (Fig. 2, I) at the light

housing until it locks into place.

2. Turn on the device with the On/Off switch (Fig. 2, B).

Operation

Models LS standard and LG standard (Fig. 2+3)

1. Turning on the device

1. Open the barn doors (Fig. 3, M).

2. Turn on the device with one of the two On/Off switches

(Fig. 2, B/D) according to the selected power source. An

acoustic signal sounds.

3. Adjust the brightness with the stepless dimmer.

2. Adjusting the brightness

The brightness can be adjusted with the dimmer (Fig. 2, C).

The changing of the setting from the current to the next level

is proceeded in an eye-saving way with a low dimming speed.

3. Aligning the light source

1. Loosen the ﬁxing screws for the U-bracket

(Fig. 2, G).

2. Move the LED panel light into the desired position.

3. Tighten the ﬁxing screws for the U-bracket handtight.

4. Turning off the device

1. Turn off the device by moving one of the two On/Off switches

(Fig. 2, B or D, according to the selected power source) to

position '0'.

2. Let the device cool down.

5. Remote control (optional accessory)

1. Turn on the device with one of the two On/Off switches

(Fig. 2, B/D) according to the selected power source. An

acoustic signal sounds.

2. Follow the instructions in the manual for the remote control6

to set-up a remote connection with the lighting unit.

Models LS bi-color and LG bi-color

1. Turning on the device

1. Open the barn doors (Fig. 3, M).

2. Turn on the device with one of the two On/Off switches

(Fig. 2, B/D) according to the selected power source. An

acoustic signal sounds.

3. If the LEDs will not light after switching the device on (LCD

shows „OFF“), press the adjustment knob (Fig. 2, C) for the

LED brightness to turn on the LED panel light manually.

2. Adjusting the colour temperature and brightness

The colour tempearture and brightness of this LED panel light

can be set individually. Therfore the colour temeprature can be

set autmatically or manually. Select from the available modes by

pressing the adjustment knob for the colour temperature (Fig.

2, K). The changing of the setting from the current to the next

level is proceeded in an eye-saving way with a low dimming

speed.

2.1. Automatic colour temperature setting (F1)

Press the adjustment knob (Fig. 2, K) for colour temperature

several times until the LCD shows „F1“. The set colour

temperature (3200K – 5600K) is shown in the upper right

display area. Change the colour temperature in steps of 100K

by turning the colour temperature controller (Fig. 2, K). The set

brightness is shown in the lower right display area. Change the

brightness in steps of 1 by turning the dimmer controller (Fig.

2, C). The adjustment range is between 10 and 30. 10 stands

for the lowest and 30 for the highest value.

2.2. Manual colour temperature setting (F2)

Press the adjustment knob (Fig. 2, K) for colour temperature

several times until the LCD shows „F2“. The brightness of the

orange LED elements is shown in the upper right display area.

Change the brightness of the orange LEDs in steps by turning

the colour temperature controller (Fig. 2, K).

The brightness of the white LED elements is shown in the lower

right display area. Change the brightness of the white LEDs in

steps by turning the dimmer (Fig. 2, K).

The adjustment range for both LED groups is between 0.1 and

30. 10 stands for the lowest and 30 for the highest value. If the

value is 0, the respective group of LEDs is switched off.

3. Aligning the light source

1. Loosen the ﬁxing screws for the U-bracket

(Fig. 2, G).

2. Move the LED panel light into the desired position.

3. Tighten the ﬁxing screws for the U-bracket handtight.

4. Turning off the device

1. Press the adjustment knob (Fig. 2, C) for the LED brightness

to turn off the LED panel light. The LCD shows „OFF“.

2. Turn off the device by moving one of the two On/Off switches

(Fig. 2, B or D, according to the selected power source) to

position '0'.

2. Let the device cool down.

5. Remote control (optional accessory)

1. Turn on the device with one of the two On/Off switches

(Fig. 2, B/D) according to the selected power source. An

acoustic signal sounds.

2. Follow the instructions in the manual for the remote control6

to set-up a remote connection with the lighting unit.

Optional accessories

Wireless remote control YK-2

Art. No. F001186

- Wireless control (up to 60 meters)

- For brightness and colour temperature settings

- Operation up to 9 devices of the same series with only one

remote control

V-Lock Li-Ion battery 190Wh

Art. No. F001631

- V-Lock connection

- Displaying the remaining battery powerRestladung

- Voltage: 14,8V

- Capacity: 190Wh

Much more accessories such as light modiﬁers, tripods and

bags available in our webshop at

www.photostudio-equipment.com

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bresser LED - LG-Serie Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info