Bedienungsanleitung Brita PURITY 450 Steam (Seite 25 von 142) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch)

497161

Zoom out

Zoom in

Vorherige Seite

1/142

Nächste Seite

4.2 Assembling the Pressure Vessel and the Pressure Vessel Lid

• Stand with both feet on the kick loops

• Lift the pressure vessel

and turn it clockwise until the mantle handles

are over the kick loops

• Remove the transport protective cap

from the ﬁ lter cartridge.

• Check that the O-ring seal of the ﬁ lter cartridge

is correctly seated in the

groove and also check for dirt and damage.

Note: lubricant at the factory.

• Stand on the kick loops

with both feet and place the pressure vessel lid

on the pressure vessel

. The position of the arrow marking on the lid

handle

must match the “INSERT” groove.

• Press the pressure vessel lid

down and turn clockwise until the lock

engages.

4.3 Assembly of Inlet and Outlet Hoses

Note: The inlet and outlet hoses are not included in the standard scope of delivery. The use of

BRITA hose sets is recommended (Chapter 13).

• Fit inlet hose

at the inlet of the connector head

and outlet hose

at the outlet of the con-

nector head

Note: Inlet “IN” and outlet “OUT” of the connector head

are equipped with O-rings as

seals, therefore no additional ﬂ at seals may be used here. Check that the O-rings are seated

correctly.

Caution: The max. tightening torque at the 1" and 3/4" connections must not exceed 15 Nm!

Only hose connections with ﬂ at seals may be used. Hoses with conical screwed connections dam-

age the ﬁ lter head connections and invalidate any guarantee claims. Only hoses that comply with

DVGW-W 543 may be used to connect the device.

Before assembly, note the direction of ﬂ ow on the upper side of the ﬁ lter head, “IN” = water inlet,

“OUT” = water outlet. Prior to installation, note installation dimensions and operating position

(Chapter 12). If no original hoses are used, the 1"–3/4"

adapter supplied must be used to ensure

the return valve is sealed correctly (pre-ﬁ tted in the water inlet).

5 Commissioning a New Filter

5.1 Bypass Setting for Filter Systems without and with Measuring and Display Unit

• Identify the local carbonate hardness in German hardness °dH (BRITA nomenclature °KH) using

the enclosed carbonate hardness test.

• Check the bypass setting on the bypass screw

Note: The bypass has been set to Position 1 in the factory, and must be changed to suit the

local carbonate hardness and the application (Chapter 7).

5.2 Commissioning the Filter Systems with Measuring and Display Unit

Representation in operating mode

Local Carbonate

Hardness Set

Type/

By-Pass Proportion

Date Field: Installation or

last ﬁ lter change date

Available residual

capacity in litres

Bar Display

Flow Symbol

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Brita PURITY 450 Steam Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info