Bedienungsanleitung BRK HS-4705-400 (Seite 8 von 29) (Englisch)

606847

Zoom out

Zoom in

Vorherige Seite

1/29

Nächste Seite

Page 14 Page 15

passWord setup

Setting Up Passwords

When you ﬁrst startup your DVR, you are automatically logged in as the ADMIN

under Device ID: 000000. By default, passwords are disabled on the system. You

will not need a password to log in or access menus. You will not need a pass-

word to access your system using the browser-based remote software.

The system employs two levels of user authorities connected to a Device ID. The

levels are as follows:

1. ADMIN (administrator): Has full control of the system, and can change both

administrator and user passwords and enable/disable password checking

2. USER (normal user): Only has access to live viewing, search, playback, and

other limited authorities.

For security reasons, it is highly recommended to enable passwords on your

system. If you enable passwords, you must select a 6-digit ADMIN password

and a 6-digit USER password. The ADMIN and USER passwords must not be

the same.

To customize Password settings, click BASIC from the Main Menu, then click

PASSWORD. You are now in the PASSWORD Menu. From here you can change the DEVICE ID:

1. Device ID: Click the ﬁeld beside Device ID and enter a 6-digit numerical Device ID using the Virtual Keyboard.

Next, in the PASSWORD drop down menu click ENABLE to set up Admin and User passwords. NOTE: Only the Administrator can

enter the PASSWORD setup.

• PASSWORD: Password must be 1-6 digits

• RETYPE: You must retype the passwords.

• NETWORK PW CLEAN: When activated, it means you will not have to use a password to log on to the system remotely via

Internet Explorer. This does not disable the DVR logon password requirement. You will still need a password to log in the DVR

if one was setup.

InItIal setup

system operation

InItIal setup

system operation

Main Menu Access

To open the Main Menu: Right-click anywhere on-screen to open the Quick Access

Menu and select MAIN MENU (mouse only), or press the MENU button on the remote

control or front panel of the system.

NOTE: If passwords are enabled on the system, you need to select your Device ID and

enter the 6-digit numerical password to open the Main Menu.

Main Menu

1. SEARCH: Search for recorded video on the system.

2. RECORD: Conﬁgure recording parameters (quality, resolution), set record

modes, and enable/disable audio recording. Note: Audio capable cameras (not

included) are required for audio recording on the system.

3. HDD: Display hard drive status and format the internal hard drive of the system.

4. BASIC: Open the Basic Setup Menu, which lets you set the system language,

date and time, device IDs and passwords, and conﬁgure display, audio and

video settings.

5. ADVANCE: Opens the Advanced Setup Menu, which lets you view system info,

conﬁgure alarm, PTZ, motion detect, maintenance, mobile, and network settings.

6. EXIT: Closes the Main Menu.

Quick Access Menu

When using the mouse, use the Quick Access Menu to access several system

options, including the Main Menu. Select one of the following options:

• MAIN MENU: Opens the main system menu

• KEYLOCK: Requires User Login to access menus

• CHN SWITCH: Select type of split-screen display

• VIDEO SEARCH: Open the Search Menu to view recorded video

• PTZ : Opens the PTZ control menu

• MUTE: Mute listen-in audio on the system. Recording of audio is still enabled.

• MANUAL REC: Start manual recording

• STOP REC: Stop manual recording

• ROTATION: Sets the time each channel is visible when rotating through chan-

nels. The Loop Time in seconds is set in the Video Setup Screen

• START CRUISE: Click to start preset PTZ Camera motion

• STOP CRUISE: Click to stop preset PTZ Camera motion

• STANDBY: Puts system in standby mode.

To close the Sub-Menu, click anywhere on-screen.

User Password Setup

Main Menu

Main Viewing Screen

Showing No HDD in DVR

Live View Screen

The Live View Screen is the home or main viewing screen. It shows live video of all current

cameras connected to the DVR. You can double-click a channel at any time to view it

in single-channel mode. You access all menus from this Live View screen via the Quick

Access Menu. You will also see the Channel number or name, time and day information

(see page 16 “Camera Display Setup” for customizing the Live View Screen). It is also

where you will see various information and warning icons, depending on what is happening

in the system or with the alarms that may be set.

【R

】 means the channel is recording

【M

】 means motion detection alarm activated on the channel

【I

】 means an input on the alarm block activated on the channel

【H

】 means either the hard drive is not installed, it is bad or it is full

【B

】 means Tamper Alarm has been activated on the channel

No HDD installed

NOTE: If there is no HDD installed, or the HDD is not recognized, or the HDD is not formatted in Live

View a red【H】will be displayed in the video preview interface. You must format the HDD in the DVR

before ﬁrst use. See: Menu > HDD management > Format. After formatting, the system will restart.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

BRK HS-4705-400 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info