Bedienungsanleitung Brother BE-1204B-BC - PC control (Seite 243 von 262) (Englisch)

644489

243

Zoom out

Zoom in

Vorherige Seite

1/262

Nächste Seite

BE-1204B-BC • BE-1206B-BC 11-3

Chapter 11 Error code list

Code Error Measures

E-13

This is displayed in case that the machine had

been shut down while the hoop was moving

and now is started up in a mode without the

home position detection, or in case that the

machine is started up in a mode without the

home position detection after pressing the CAP

SW to change the hoop.

Press the

to start the home position moving.

E-14 Y-axis home position error

Turn the power off and on once. If the same error occurs

again, the Y-axis mechanism is faulty.

E-15

Stop error during SSP processing (when

pressing the stop key while the hoop is moving)

Hoop movement restarts if you press

E-16

Needle bar No. of the destination is out of

range

Press the

, or turn ON the F/B switch on the head to either

side to cancel the error and set up the needle bar setting again.

E-17 Speed range is out of range This is not usually displayed.

E-18 X-axis stepping motor connector error

Turn the power off and on once after checking to see that the

connector of the X-axis stepping motor is properly connected.

E-1A Destination coordinates error

E-1B

The machine has reached the mending stop

position.

This is not usually displayed.

E-1C The machine stops during mask tracing.

Tracing is cancelled if the

key is pressed when the

machine is stopped during mask tracing. Press the

key

to continue tracing.

E-1D

The machine stops while the needle is moving

between patterns during repeat sewing.

This is displayed when the stop switch is pressed while the

hoop is moving. Press the

to move the hoop again. (It

is necessary to press the

again to start sewing.)

Errors E-1C and E-1D are not displayed due to mechanical problems.

E-1E

When the power is turned on, bed can not be

retracted.

E-1F

Presser foot down error while searching for

home position just after the power is turned on.

This is not displayed in this model.

E-21 Hoop overhang (+X)

E-22 Hoop overhang (+Y)

E-23 Hoop overhang (+X, +Y)

E-24 Hoop overhang (-X)

E-25 Hoop overhang (+X, -X)

E-26 Hoop overhang (-X, +Y)

Pattern or the needle position is out of the embroidering area.

Reset the embroidering area with the PC or move the hoop to

the sewable position.

E-27 Hoop overhang (+X, -X, +Y)

E-28 Hoop overhang (-Y)

E-29 Hoop overhang (+X, -Y)

Pattern or the needle position is out of the embroidering area.

Reset the embroidering area with the PC or move the hoop to

the sewable position.

E-2A Hoop overhang (+Y, -Y)

E-2B Hoop overhang (+X, +Y, -Y)

E-2C Hoop overhang (-X, -Y)

E-2D Hoop overhang (+X, -X, -Y)

E-2E Hoop overhang (-X, +Y, -Y)

E-2F Hoop overhang (+X, -X, +Y, -Y)

E-31 Needle overhang (+X)

E-32 Needle overhang (+Y)

E-33 Needle overhang (+X, +Y)

E-34 Needle overhang (-X)

Pattern or the needle position is out of the embroidering area.

Reset the embroidering area on the panel or move the hoop to

the sewable position.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Brother BE-1204B-BC - PC control Seite 243

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info