Bedienungsanleitung Brother Innov-is 6750D (Seite 354 von 380) (Englisch)

613559

354

Zoom out

Zoom in

Vorherige Seite

1/380

Nächste Seite

TROUBLESHOOTING

352

Fabric puckers There is a mistake in the upper or bobbin

threading.

Check the steps for threading the machine

and rethread it correctly.

54, 57

Using improper needle or thread for the

selected fabric.

Check the “Fabric/Thread/Needle

Combination” chart.

Thread tension is set incorrectly. Adjust the thread tension. 79, 233

Stitches are too long when sewing thin fabrics. Shorten the stitch length. 79

Needle is turned, bent or the point is dull. Replace the needle. 67

Spool cap is set incorrectly. Check the method for attaching the spool cap,

then reattach the spool cap.

Wrong presser foot. Use the correct presser foot. “STITCH SETTING

CHART”

High-pitched sound

while sewing

Dust or lint is caught in the feed dogs. Remove the dust or lint. 338

Pieces of thread are caught in the race. Clean the race. 338

Upper threading is incorrect. Check the steps for threading the machine

and rethread the machine.

There are scratches on the race. Replace the race, or consult your authorized

dealer.

338

A bobbin designed specifically for this machine

is not used.

Incorrect bobbins will not work properly. Only

use a bobbin designed specifically for this

machine.

Character pattern

does not turn out

Wrong presser foot was used. Attach the correct presser foot. “STITCH SETTING

CHART”

Pattern adjustment settings were set incorrectly. Revise the pattern adjustment settings. 162

Did not use a stabilizer material on thin fabrics

or stretch fabrics.

Attach a stabilizer material. 161

Thread tension is set incorrectly. Adjust the thread tension. 79, 233

Fabric was pulled, pushed or fed at an angle

while it was being sewn.

Sew while guiding the fabric with your hands

so that the fabric is fed in a straight line.

Embroidery pattern

does not sew out

correctly

Thread is twisted. Use scissors, etc., to cut the twisted thread

and remove it from the race, etc.

—

Fabric was not inserted into the frame correctly

(fabric was loose, etc.).

If the fabric is not stretched tight in the frame,

the pattern may turn out poorly or there may

be shrinkage of the pattern. Set the fabric into

the frame correctly.

203

Stabilizing material was not attached. Always use stabilizing material, especially

with stretch fabrics, lightweight fabrics, fabrics

with a coarse weave, or fabrics that often

cause pattern shrinkage. See your authorized

dealer for the proper stabilizer.

200

There was an object placed near the machine,

and the carriage or embroidery frame hit the

object during sewing.

If the frame bumps something during sewing,

the pattern will turn out poorly. Do not place

anything in the area where the frame may

bump it during sewing.

218

Fabric outside the frame edges interferes with

the sewing arm, so the embroidery unit cannot

move.

Reinsert the fabric in the embroidery frame so

that the excess fabric is away from the sewing

arm, and rotate the pattern 180 degrees.

203

Fabric is too heavy, so the embroidery unit

cannot move freely.

Place a large thick book or similar object

under the arm head to lightly lift the heavy

side and keep it level.

—

Fabric is hanging off the table. If the fabric is hanging off the table during

embroidery, the embroidery unit will not move

freely. Place the fabric so that it does not hang

off the table or hold the fabric to keep it from

dragging.

218

Fabric is snagged or caught on something. Stop the machine and place the fabric so that

it does not get caught or snagged.

—

Embroidery frame was removed during sewing

(for example, to reset the bobbin). The presser

foot was bumped or moved while removing or

attaching the embroidery frame, or the

embroidery unit was moved.

If the presser foot is bumped or the

embroidery unit is moved during sewing, the

pattern will not turn out. Be careful when

removing or reattaching the embroidery frame

during sewing.

229

abilizer is incorrectly attached, for example, it

is smaller than the embroidery frame.

Attach the stabilizer correctly. 200

Problem Cause Solution Page

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Brother Innov-is 6750D Seite 354

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Brother Innov-is 6750D

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info