Bedienungsanleitung Brother Innov-is F440E (Seite 92 von 100) (Englisch)

718742

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

Troubleshooting

A-8

Upper thread

breaks.

Machine is not threaded correctly (used the

wrong spool cap, spool cap is loose, the thread

did not catch the needle bar threader, etc.).

Rethread the machine correctly. B-19

Knotted or tangled thread is being used. Remove any knots or tangles. –

Upper thread tension is too strong. Adjust the thread tension. E-26

Thread is tangled. Use scissors, etc., to cut the tangled thread and

remove it from the race, etc.

A-2

Needle is turned, bent or the point is dull. Replace the needle. B-23

Needle is installed incorrectly. Reinstall the needle correctly. B-23

There are scratches near the hole in the

embroidery foot.

Replace the embroidery foot, or consult your

authorized Brother dealer.

A-5

There are scratches on the bobbin case. Replace the bobbin case, or consult your

authorized Brother dealer.

A-2

Using improper needle or thread for the

selected fabric.

Check the information about the needle and

thread to be used.

B-23

While embroidering, the thread became knotted

or tangled.

Rethread upper and lower thread. B-17, B-19

A bobbin designed specifically for this machine

is not used.

Incorrect bobbins will not work properly. Only

use a bobbin designed specifically for this

machine.

B-14

The thread is

tangled on the

wrong side of the

fabric.

Upper threading is incorrect. Check the steps for threading the machine and

rethread the machine. Be sure that the

embroidery foot is in the raised position when

threading the machine so that the upper thread

sets properly in the upper tension.

B-19

Using improper needle or thread for the

selected fabric.

Check the information about the needle and

thread to be used.

B-23

The upper thread is

too tight.

The bobbin thread is incorrectly installed. Correctly install the bobbin thread. B-17

Bobbin thread

breaks.

Bobbin is set incorrectly. Reset the bobbin correctly. B-17

Bobbin thread is incorrectly wound. Use a correctly wound bobbin. B-17

There are scratches on the bobbin or it doesn’t

rotate properly.

Replace the bobbin. B-14

Thread is tangled. Use scissors, etc. to cut the tangled thread and

remove it from the race, etc.

A-2

A bobbin designed specifically for this machine

is not used.

Incorrect bobbins will not work properly. Only

use a bobbin designed specifically for this

machine.

B-14

Fabric puckers.

There is a mistake in the upper or bobbin

threading.

Check the steps for threading the machine and

rethread it correctly.

B-19

Spool cap is set incorrectly. Check the method for attaching the spool cap,

then reattach the spool cap.

B-14

Needle is turned, bent or the point is dull. Replace the needle. B-23

Skipped stitches

Machine is threaded incorrectly. Check the steps for threading the machine and

rethread it correctly.

B-19

Needle is turned, bent or the point is dull. Replace the needle. B-23

Needle is installed incorrectly. Reinstall the needle correctly. B-23

The needle is worn/damaged. Replace the needle. B-23

Dust or lint has collected under the needle

plate.

Remove the dust or lint with the brush. A-2

Symptom Probable Cause Remedy Reference

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Brother Innov-is F440E Seite 92

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Brother Innov-is F440E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info