Bedienungsanleitung Brother Innov-is F440E (Seite 94 von 100) (Englisch)

718742

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

Troubleshooting

A-10

Error messages

When erroneous operations are performed messages and advice on operation will be displayed on the LCD. Follow what is

displayed. If you press or do the operation correctly while the error message is displayed, the message disappears.

Embroidery pattern

does not sew out

correctly.

Fabric outside the frame edges interferes with

the sewing arm, so the embroidery unit cannot

move.

Reinsert the fabric in the embroidery frame so

that the excess fabric is away from the sewing

arm, and rotate the pattern 180 degrees.

B-30

Fabric is too heavy, so the embroidery unit

cannot move freely.

Place a large thick book or similar object under

the arm head to lightly lift the heavy side and

keep it level.

–

Fabric is hanging off the table. If the fabric is hanging off the table during

embroidery, the embroidery unit will not move

freely. Place the fabric so that it does not hang

off the table or hold the fabric to keep it from

dragging.

B-28

Fabric is snagged or caught on something. Stop the machine and place the fabric so that it

does not get caught or snagged.

–

Embroidery frame was removed during sewing

(for example, to reset the bobbin). The

embroidery foot was bumped or moved while

removing or attaching the embroidery frame, or

the embroidery unit was moved.

If the embroidery foot is bumped or the

embroidery unit is moved during sewing, the

pattern will not turn out. Be careful when

removing or reattaching the embroidery frame

during sewing.

B-33

Stabilizer is incorrectly attached, for example, it

is smaller than the embroidery frame.

Attach the stabilizer correctly. B-29

Loops appear on

the surface of the

fabric when

embroidering.

The thread tension is incorrectly set. Adjust the thread tension. E-26

The combination of the bobbin case and bobbin

thread is incorrect.

Change the bobbin case or bobbin thread so

that the correct combination is used.

B-28

Error messages Cause/solution

A malfunction occurred. Turn the machine off, then

on again.

This message is displayed if some malfunction occurs.

Turn the machine off, then back on again.

If this message continues to appear, the machine may be malfunctioning.

Please contact your authorized Brother dealer or the nearest Brother

authorized service center.

Cannot change the configuration of the characters. This message is displayed when there are too many characters and the

curved character configuration is impossible.

Cannot change the font since some letters are not

included to the selected font.

This message appears when the font of the embroidery character pattern is

changed to one that does not include characters used in the pattern.

Cannot recognize the data for the selected pattern.

The data may be corrupted. Please turn off the

power and turn on again.

This message appears when you try to retrieve pattern data that is invalid.

Since any of the following may be the cause, check the pattern data.

• The pattern data is damaged.

• The data that you tried to retrieve was created using another

manufacturer’s data design system.

Turn the machine off, then on again to return it to its normal condition.

Check and rethread the upper thread. This message is displayed when the upper thread is broken or not threaded

correctly, and the “Start/Stop” button, etc. is pressed.

Data volume is too large for this pattern. This message is displayed when the patterns you are editing take up too

much memory, or if you are editing too many patterns for the memory.

Lower the presser foot lever. This message is displayed when a button, such as the “Start/Stop” button,

was pressed while the presser foot was raised.

Not enough available memory to save. This message is displayed when the memory is full and the pattern cannot

be saved.

Symptom Probable Cause Remedy Reference

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Brother Innov-is F440E Seite 94

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Brother Innov-is F440E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info