718903
15
Zoom out
Zoom in
Vorherige Seite
1/75
Nächste Seite
Setting Up the Printer
11
1
Connecting the Printer
and iOS Device
1
NOTE
This printer can establish a connection
with the “Open System” authentication
method and when the encryption method
is set to “None” or the “WEP” ad-hoc
mode.
While connected to this printer in ad-hoc
mode, Wi-Fi cannot be used to connect
to the Internet. In addition, when the iOS
device enters sleep mode, the connection
between the printer and iOS device will
be cut.
Printing From an iOS Device
Via a Wireless LAN Connection1
The default printer settings are listed below.
It may be useful to first print a report of the
printer settings as described in Printing a
Printer Report on page 59.
SSID (network name): PJ-673_XXXX (where
“XXXX” is the last four digits
of the printer’s
serial number)
Encryption method: WEP
WEP key: Last five digits
of the printer’s
serial number
IP address: 169.254.100.1
Subnet mask: 255.255.0.0
NOTE
The serial number appears as “SER. NO.
XXXXXX-XXXXXXXXX” on the back of
the printer.
Connecting the Printer
(With the Default Settings)
1
Follow this setup method when using the
printer’s factory default settings to connect an
iOS device. To change the printer settings,
see Setting Up the Printer (With the Default
Settings Changed) on page 12.
In addition, if the printer’s wireless LAN
settings are changed, even after they had
already been specified, the connection
between the iOS device and the printer must
be re-established.
a Turn on the printer.
b Check that the POWER indicator is lit,
and then hold down (at least 3 seconds)
the (Power) button to enter wireless
LAN mode. Check that the WIRELESS
LAN indicator is blinking. For details,
see Switching Between Wireless LAN
Mode and USB Mode on page 30.
c Start Settings on the iOS device.
d Select .
If is set to [Off], change it to [On].
e A list of Wi-Fi networks (SSID) that can
be joined appears.
To establish a connection, tap the
printer’s default network (SSID) so that
a checkmark appears beside the
network (SSID). For the password, type
in the default WEP key (last five digits
of the serial number). It will take time for
the iOS device to search for the SSID
and display it. If it is not displayed, set
Wi-Fi to [Off], then to [On] again.
When printing from an iOS device,
printing software created by a software
developer will be needed in addition
to the product and services that we
provide. (We provide an SDK that can
be used.) Consult with a software
developer for printing software for the
iOS device.
15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Brother PJ-673 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Brother PJ-673

Brother PJ-673 Bedienungsanleitung - Deutsch - 76 seiten

Brother PJ-673 Bedienungsanleitung - Holländisch - 75 seiten

Brother PJ-673 Bedienungsanleitung - Französisch - 81 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info