Bedienungsanleitung Buderus SSB512 (Seite 13 von 68) (Englisch)

636469

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

SSB 6720818454 (2016/02) US

Regulations | 13

3 Regulations



Observe all rules, regulations, standards and guidelines

applicable to the installation and operation of this appliance

in your country.



In the Commonwealth of Massachusetts, this appliance

must be installed by a licensed plumber or gas tter. Valves

external to the boiler must be tted with T-handles and

condensate piping must be installed in accordance with the

State Plumbing Code.

3.1 Compliance with standards and regulations

The installation must conform to the requirements of the authority having

jurisdiction or, in the absence of such requirements, to the latest edition

of the National Fuel Gas Code, ANSI Z223.1./NFPA 54. In Canada,

installation must be in accordance with the requirements of CAN/CSA

B149.1, Natural Gas and Propane Installation Code.

This condensing gas boiler complies in its design and mode of operation

with the American National Standard ANSI Z21.13/CSA4.9, latest edition

for Gas Fired Low Pressure Steam and Hot Water Boilers.

Other conrmed approvals and certications are indicated by labels on

the boiler.

Where required by the authority having jurisdiction, the installation

must conform to the Standard for Controls and Safety Devices for

Automatically Fired Boilers, ANSI/ASME CSD-1.

Install CO detectors per local regulations. Boiler requires yearly

maintenance (see section “7 Maintenance”).

3.2 Operating limits of the boiler

The heat exchanger has been designed and certied in accordance with

the ASME Boiler and Pressure Vessel Code, Section IV.

The hot water distribution system must comply with all applicable codes

and regulations. When replacing an existing boiler, it is important to

check the condition of the entire hot water distribution system to ensure

safe operation. Common practice calls for inspecting an existing system

in its entirety and bringing it up to code. All pipework should be properly

cleaned and ushed.

3.3 Additional regulations for installation in

Massachusetts

(a) For all side wall horizontally vented gas fueled equipment installed in

every dwelling, building or structure used in whole or in part for residential

purposes, including those owned or operated by the Commonwealth and

where the side wall exhaust vent termination is less than seven (7) feet

[2150 mm] above nished grade in the area of the venting, including but

not limited to decks and porches, the following requirements shall be

satised:

• INSTALLATION OF CARBON MONOXIDE DETECTORS. At the

time of installation of the side wall horizontal vented gas fueled

equipment, the installing plumber or gastter shall observe that a hard

wired carbon monoxide detector with an alarm and battery back-

up is installed on the oor level where the gas equipment is to be

installed. In addition, the installing plumber or gastter shall observe

that a battery operated or hard wired carbon monoxide detector

with an alarm is installed on each additional level of the dwelling,

building or structure served by the side wall horizontal vented gas

fueled equipment. It shall be the responsibility of the property owner

to secure the services of qualied licensed professionals for the

installation of hard wired carbon monoxide detectors.

- In the event that the side wall horizontally vented gas fueled

equipment is installed in a crawl space or an attic, the hard wired

carbon monoxide detector with alarm and battery back-up may be

installed on the next adjacent oor level.

- In the event that the requirements of this subdivision can not be

met at the time of completion of installation, the owner shall have

a period of thirty (30) days to comply with the above requirements;

provided, however, that during said thirty (30) day period, a

battery operated carbon monoxide detector with an alarm shall be

installed.

• APPROVED CARBON MONOXIDE DETECTORS. Each carbon

monoxide detector as required in accordance with the above

provisions shall comply with NPA 720 and be ANSI/UL 2034 listed and

IAS certied.

• SIGNAGE. A metal or plastic identication plate shall be permanently

mounted to the exterior of the building at a minimum height of eight (8)

feet above grade directly in line with the exhaust vent terminal for the

horizontally vented gas fueled heating appliance or equipment. The

sign shall read, in print size no less than one-half (.) inch in size, “GAS

VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.

• INSPECTION. The state or local gas inspector of the side wall

horizontally vented gas fueled equipment shall not approve the

installation unless, upon inspections, the inspector observes carbon

monoxide detectors and signage installed in accordance with the

provisions of 248 CRM 5.08(2)(a) 1 through 4.

(b) EXEMPTIONS: The following equipment is exempt from 248 CRM

5.08(2)(a) 1 through 4:

• The equipment listed in Chapter 10 entitled “Equipment Not Required

To Be Vented” in the most current edition of NFPA 54 as adopted by

the board; and

• Product Approved side wall horizontally vented gas fueled equipment

installed in a room or structure separate from the dwelling, building or

structure used in whole or in part for residential purposes.

VENTING SYSTEM REQUIRED. When the manufacturer of Product

Approved side wall horizontally mounted gas equipment provides a

venting system design or venting system components with the equipment,

the instructions provided by the manufacturer for the installation of the

equipment and venting shall include:

• Detailed instructions for the installation of the venting system or the

venting system components; and

• A complete parts list for the venting system design or venting system.

(d) MANUFACTURERS REQUIREMENTS - GAS EQUIPMENT

VENTING SYSTEM NOT PROVIDED. When the manufacturer of Product

Approved side wall horizontally vented gas fueled equipment does not

provide the parts for the venting of ue gases, but identies special

venting systems, the following requirements shall be satised by the

manufacturer:

• The referenced special venting systems shall be included with the

appliance or equipment installation instructions; and

• The special venting systems shall be Product Approved by the Board,

and the instructions for that system shall include a parts list and

detailed installation instructions.

(e) A copy of all instructions for all Product Approved side wall horizontally

vented gas fueled equipment, all venting instructions, all parts lists for

venting instructions, and/or venting design instructions shall remain with

the appliance or equipment at the completion of the installation.

Buderus SSB512 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Buderus SSB512

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info