Bedienungsanleitung Buderus SSB512 (Seite 15 von 68) (Englisch)

636469

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

SSB 6720818454 (2016/02) US

Installation | 15

4.3 Water Chemistry Guidelines

NOTICE: If using anti-freeze:

► Follow the boiler manufacturer’s instructions on

antifreeze concentration.

► Frost protection and inhibitor level has to be checked

annually during the regular scheduled maintenance of

the condensing boiler.

NOTICE: System damage!

► It is the installer’s responsibility to ensure that the

heating system is compatible with the boiler type and

size installed.

► pH-value of the heating water to be kept between 6.5

and 9.

To avoid any presence of oxygen in the system, it is advised to prevent as

little as possible air during installation. Usual spots where air is most likely

to seep in are: gaskets, pumps, air vents and O-rings gaskets. Using

an automatic water ll system exposes the system to fresh oxygenated

water. In commercial applications it is recommended to install a water

meter to measure the introduction of fresh water into the system.

A minimum water pressure is required for optimum performance.

Minimum water pressure required: 7.25 psi (0.5 bar).

Before and during assembly, the system must be kept free of impurities,

construction dust, sand, copper dust, grease, carbon deposits, etc., as

well as welding ux residue. In any of these instances, the old system

must be rinsed with clear water mixed with a highly concentrated rinse

agent.

For freeze protection use only propylene glycol, with scale inhibitors, with

a maximum volume [concentration] of 40% of glycol.



NOTICE: DO NOT use PVC for exhaust venting when using

anti-freeze in the primary circuit of the boiler. Use CPVC, PP

or stainless steel only!

Water hardness must fall within the following limits:

50 ppm of CaCO

< (alkali strength) < 150 ppm of CaCO

► Use only untreated water to ll the system.

► Do not use TSP (tri-sodium phosphate).

► Do not use ll water treated with salt bedding type exchangers (ion

exchanger).

► Never introduce non-approved boiler treatment or similar additives.

► Only use ll water with a hardness below 7 grains.

► Filling with chlorinated water is acceptable if chlorine levels are below

100 ppm.

► Consult a local water treatment specialist for recommendations if any

of the above is outside the stated ranges.

► When using oxygen permeable PEX, the system must be separated

from the boiler by a heat exchanger.

► A correctly sized and working expansion vessel must be installed.

► Do not exceed the maximum permissible ow rate through the boiler.

► Excessive ow can cause erosion damage to the heat exchanger.

► Eliminate System Leaks:

Continuous addition of make-up water will constantly add oxygen to

the system and lead to corrosion. All system leaks must be repaired.

In the following table are listed the chemical water specications.

Parameters Units Value

General feature - Colorless, no sediment

Dissolved Oxygen mg/l < 0,05

Total iron (Fe) mg/l < 0,3

Total copper (Cu) mg/l < 0,1

mg/l < 10

mg/l < 3

mg/l < 15

Tab. 1 Water specication

4.4 Hydraulic connection

Hydraulic connection are shown in Fig. 2, Fig. 3 and Fig. 4. In the

following table are listed the pipe dimension for each model:

Model

Ø Water supply

connection

Ø Water return

connection

SSB255 1-1/2” NPT male 1-1/2” NPT male

SSB399 1-1/2” NPT male 1-1/2” NPT male

SSB512 2” NPT male 2” NPT male

NOTICE: Before connecting the boiler to the heating

system, ush the heating system to remove sediment, ux,

dirt, and other foreign matter. The heat exchanger may be

damaged by sediment or corrosion.

• Do not use cleaning uids that are not compatible with the boiler

materials, including acids (e.g. hydrochloric acid and similar ones) at

any concentration

• Introducing fresh water to the system increases the oxygen presence

and can cause corrosion of metallic components. Immediately repair

any drips or leaks in the system to avoid constant introduction of air

into the system.

• Do not use the water contained in the boiler for domestic use or as

drinking water or within swimming pools.

• Excessive uctuation in pressure changes in the system can cause

fatigue and stress on the heat exchanger. This is detrimental to the

integrity of the boiler and system components, it is mandatory to

maintain a constant operating pressure.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Buderus SSB512 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Buderus SSB512

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info