Bedienungsanleitung Bushnell Onix 350 (Seite 12 von 28) (Englisch)

481954

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

EXPLORING THE PAGES : MAP & Info Boxes

1. Go to the MAP page if you are not already there (this example will use the

MAP Page as a starting point, but Info Boxes are available on other Pages as

well).

2. Hold the MENU button for 2 sec. You will see a “Nav” tab pop up above the

lower set of Info Boxes, and the ﬁrst Info Box is highlighted.

3. Press OK to see a list of the diﬀerent types of information available to display

in the Info Box (Fig. 7). Four sets of lists are available-use the “+” and “-“

buttons to see the other lists.

4. Use UP/DOWN buttons to highlight one of the listed options (for example,

“Local Time” from the 3rd list) (Fig. 8), then press OK to checkmark it (press

EXIT to return without changing the selected Info Box). e ﬁrst Info Box will

change to display the local time-your new selection has replaced the previous

type of info.

5. Press DOWN to select the second Info Box and repeat steps 3 & 4 to change

what is displayed in this box. Repeat the process again if you like for the third

box. Note that if you choose “Location” (your latitude/longitude) for one of

your info boxes, it will take up 2 Info Boxes (latitude is the top box).

6. You may have noticed that there is an option at the top of the ﬁrst list of

information types labeled “No Information”. You may select this option for any

of the Info Boxes if you prefer not to use one or more of them-as selecting “No

Information” will actually clear and remove that Info Box “slot” from the lower

set of boxes. You can reduce the “stack” of three boxes you start with to just

two, one or even zero. You can also press DOWN to step below the third box,

where you will ﬁnd that a fourth box is “hidden” because “No Information” is

selected for display there. Simply select something else, and you can have up to

a maximum of 4 Info Boxes in the lower part of your Map screen (Fig. 9).

7. Once you have set up the lower Info Boxes with a few diﬀerent types of Nav

data, press EXIT or hold MENU again to leave the Info Box setup process and

return to normal display. e info you chose will still be displayed in the boxes,

and any boxes with “No Information” selected will not appear.

8. You can also change the info displayed in the upper two Info Boxes, but

these can only be used to show Nav related data. After following step 2 above to

highlight the ﬁrst lower Info Box, press UP and you will jump to the upper left

Info Box. Press OK to see the list of info to display here (then press “+” to see a

second list). As described in step 4, make a selection from one of the lists, then

press OK. Press RIGHT to jump to the upper right Info Box and repeat. Once

you have one or both upper boxes set up as you like, press EXIT.

Setting Up and Using the Info Boxes-continued

Fig 7.

Info Boxes

Info Box Options (Nav)

for lower boxes

Fig 8.

MAP Page

Info Box Options

for upper boxes

Fig 9. MAP Page

4 Info Boxes After

Set Up and Exit

Upper Info Boxes

Lower Info Boxes

(0 ~ 4, set by user)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bushnell Onix 350 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info