Bedienungsanleitung Bushnell Onix 350 (Seite 21 von 28) (Englisch)

481954

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

7) My Map Areas-pick from list of your previously created custom map

areas

8) My Photos (or Topos)-after you pick a photo or topo from the list (arrow

down to it) and press OK to conﬁrm you wish to navigate towards that area,

the ONIX will begin to point you towards that area. (Note that you must have

selected photos or topos as a screen layer in your MAP options as described

earlier on page 9 if you want to see it while navigating.) Alternatively, instead

of pressing OK, you can press the RIGHT key from the name on the list

and go to the “eyeball” icon, then press OK to just view the photo or topo

without starting navigation. To exit this “view only” mode, press OK again

to return to the list.

9) Location-a latitude and longitude coordinate

• Map Details (or Compass Options) (Name varies with current display Page):

When you are on the MAP Page, this will say “Map Details”. You can decide

whether you wish to view details such as the compass, points of interest, range

rings, etc. superimposed onto the base map by toggling them on/o in the Map

Detail list. On the NAV Page, it will say “Compass Options” (see details in the

NAV Page section)

• Info Boxes: an alternate way (instead of holding MENU down) to pop up

the Info Boxes for editing. See “Setting Up and Using the Info Boxes” for more

details.

• Draw Ruler: a tool to quickly ﬁnd the distance between multiple points on

the map. After selecting “Draw Ruler” from the MAP Page HOT menu

(Fig.

33)

, either press OK and move the cursor to any point on the map, or press

the RIGHT key and chose an existing location from the To/From list

(Fig. 35)

Once a location has been selected, press OK and choose “Measure To”

(Fig.

36)

. is will create a fence post at that location. e info boxes will show

the distance from your current location to that point (fence post)

(Fig. 37)

. To

measure the distance between any two points, use the same process, except that

after a selection has been made, press “Measure From”, then repeat the process to

select a second point to “Measure To”. To add more points, select an additional

location from the map or the list and choose “Add Fence Post”. If you continue

to set additional points, you will see more options appear in the Measuring

(Fig. 38)

. You can clear all ruler guides and start over, or select “Close

Region” to turn three or more points into a Map Area and measure its area in

square yards or miles. e regions created by your rulers can be saved as Routes

or Map Areas. Open regions are saved as routes and closed regions are saved as

Map Areas. ey will be stored in My Routes and My Map Areas. A “Measuring

Info Box” is automatically displayed when drawing rulers, displaying relevant

data: Distance to Cursor, Total Length, Last Segment Length and Total Area.

• SafeTrack: select and press OK to enter SafeTrack mode, or to see the SafeTrack

options. See “SafeTrack™ Battery Conservation Mode” on the next page for more

details.

USING YOUR ONIX350 GPS RECEIVER : The HOT Button

Fig 37. Draw Ruler-

Info Box Data

Fig 35. Draw Ruler-

To/From List

Fig 36. Measuring

Menu-basic options

Fig 38. Measuring

Menu-more options

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bushnell Onix 350 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info