Bedienungsanleitung Bushnell Onix 400-2 (Seite 22 von 32) (Englisch)

481956

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

USING YOUR ONIX400 GPS RECEIVER : The HOT Button Menu

2) All Waypoints-pick from list of all stored waypoints (shown in order

beginning with the closest)

3) POI (Point of Interest)-gas stations, hospitals, airports, etc.

4) Places-built into the base map-city names, etc.

5) My Trails-pick from list of saved Trails (see next section). The ONIX will

start pointing you to the closest point on that trail. A trail is a previously

walked path, for example a trail that you took back to your campsite

that wound around trees and past the edge of a pond.

My Routes

-pick from your list of saved routes (point to point

navigation)

My Map Areas

-pick from list of your previously created custom map

areas

My Photos

(or Topos)-after you pick a photo or topo from the list (arrow

down to it) and press OK to conﬁrm you wish to navigate towards that

area, the ONIX will begin to point you towards that area. (Note that you

must have selected photos or topos as a screen layer in your MAP options

as described

earlier on page 9 if you want to see it while navigating.)

Alternatively, instead of pressing OK, you can press the RIGHT key from

the name on the list and go to the “eyeball” icon, then press OK to just

view the photo or topo without starting navigation. To exit this “view

only” mode, press OK again to return to the list.

9) Location-a latitude and longitude coordinate

• Map Detail (or Compass Options) (Name varies with current display Page):

When you are on the MAP Page, this will say “Map Details”. You can decide

whether you wish to view details such as the compass, points of interest,

range rings, etc. superimposed onto the base map by toggling them on/off

in the Map Detail list. On the NAV Page, it will say “Compass Options” (see

details in the NAV Page section)

• Info Boxes: an alternate way (instead of holding MENU down) to pop up

the Info Boxes for editing. See “Setting Up and Using the Info Boxes” for

more details.

• Draw Ruler: a tool to quickly ﬁnd the distance between multiple points

on the map. After selecting “Draw Ruler” from the MAP Page HOT menu

(Fig.

38)

, either press OK and move the cursor to any point on the map, or press

the RIGHT key and chose an existing location from the To/From list

(Fig. 40)

Once a location has been selected, press OK and choose “Measure To”

(Fig.

41)

. This will create a fence post at that location. The info boxes will show

the distance from your current location to that point (fence post)

(Fig. 42)

To measure the distance between any two points, use the same process,

except that after a selection has been made, press “Measure From”, then

repeat the process to select a second point to “Measure To”. To add more

points, select an additional location from the map or the list and choose

Fig 42. Draw Ruler-

Info Box Data

Fig 40. Draw Ruler-

To/From List

Fig 41. Measuring

Menu-Basic Options

Fig 43. Measuring

Menu-More Options

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Bushnell Onix 400-2 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info