684154
3
Zoom out
Zoom in
Vorherige Seite
1/6
Nächste Seite
4. Fitting and Changing the Gas cylinder
Before connecting the appliance to a gas cylinder, ensure that the rubber seal on the regulator
is in position and in good condition. Carry out this check each time you fit the appliance to a gas
cylinder.
Blow out any dust from the cylinder opening to prevent possible blockage of the jet.
Ensure that the appliance valves are in the OFF position by turning the control knobs fully
clockwise to their stop.
Ensure that the gas cylinder is fitted or changed in a well ventilated location, preferably
outdoors, away from any source of ignition, such as naked flames and away from other people.
Make sure that the gas cylinder is kept upright at all times and while screwing the connection to
the cylinder, hand tighten until fully engaged.
Ensure that a complete gas seal has been made (check for the smell of gas around the
connection joint). If there is a leak on your appliance (smell of gas), take it outside immediately
into a well ventilated flame free location where the leak may be detected and stopped.
To check for leaks on your appliance, do it outside using warm soapy water only, which is
applied to the joints and connections of the appliance. A formation of bubbles will indicate the
gas leak.
Do not check for leaks with a naked flame.
If you cannot rectify the gas leak, do not use the appliance, contact your local CADAC stockist for assistance.
When changing a gas cylinder, close the cylinder valve (if fitted) and then the appliance valve. Make sure the flame is extinguished before unscrewing
the regulator. Re-fit the regulator to a full cylinder following the same precautions as described above.
The appliance is designed for use with cooking vessels of not less than 150mm in diameter and not greater than 250mm in diameter.
The pot stands and aluminium grill plates can be used in any configuration (i.e. one pot stand and one grill, two grills or two pot stands).
After lighting, do not move the gas cylinder and the appliance around, as liquefied gas may enter the appliance from the gas cylinder, causing it to flare
(large yellow flames).
Always operate the appliance on a firm level surface with the gas cylinder in an upright position.
Turn the control knob clockwise to the 'OFF' position.
Turn the gas supply 'ON' at the cylinder.
Turn the control knob anti-clockwise until a hissing sound is heard, press the piezo button. This should ignite the burner.
If the burner does not stay alight, repeat as above.
To turn the stove 'OFF', turn the cylinder valve to the 'OFF' position and then turn the control knob on the appliance clockwise to the ‘OFF' position.
To light the appliance, ignite a match or barbecue lighter, turn ON the appliance valve after connecting to and opening the cylinder valve, by turning the
control knob in an anti-clockwise direction. Light the appliance burner.
Use the control knob to adjust the flame intensity to the desired level by turning the knob clockwise to decrease the flame and anti-clockwise to
increase it.
After use, close valve on gas cylinder. When the flame has extinguished close the valve on the appliance by turning knob fully clockwise.
This appliance does not require scheduled maintenance.
It is dangerous to use an appliance with a cracked or perished seal and / or tubing. Inspect both
seals and tubing regularly and replace if they are not in order, before using the appliance.
If the appliance was in use, it will be hot. Allow to cool sufficiently before attempting any
maintenance.
The stove is fitted with jets to regulate the correct amount of gas.
Should the hole in the jet become blocked this may result in a small flame or no flame at all.
Do not attempt to clean the jet with a pin or other such device as this may damage the orifice,
which could make the appliance unsafe.
Ensure that the cylinder valve is closed, and then disconnect the appliance from the gas cylinder.
Remove the self tapping screw which holds the heat deflector plate in position then remove it to
expose the venturi.
Remove the self tapping screw which holds the venturi in place.
Move the burner assembly back slightly so as to expose the valve and the jet.
Unscrew the blocked jet with a suitable spanner and replace it with a new jet.
Do not over tighten as this may damage the jet. To re-assemble, reverse the above procedure.
Do not use pliers on the jet as this may damage the jet making it unusable or impossible to
remove.
A normal flame is blue and may have a yellow tip. If the flame is completely yellow, it may be that
the jet is not securely fitted. Re-tighten the jet to give a gas tight seal. An overfilled gas cylinder
can also cause large yellow flames. The cylinder should be returned to filling station and checked
by weight.
Check that the inlet to the venturi is clear and free of obstructions.
If the flame power drops or the gas will not light, check that the gas cylinder still contains gas
(shake to hear the noise made by the liquefied gas). If there is still gas, the jet might have
become blocked or partially blocked.
If you suspect a blocked jet, follow the instructions above
WARNING: IF THE BURNER FAILS TO IGNITE WITHIN 10 SECONDS, TURN THE CONTROL KNOB OFF (CLOCKWISE). WAIT THREE
MINUTES BEFORE ATTEMPTING TO RE-LIGHT WITH IGNITION SEQUENCE.
Lighting the Appliance with a Match
Replacing a Blocked Jet
.
5. Using the Appliance
6. General Maintenance
screw
screw
Heat
deflector
plate
screw
venturi
Jet
valve
7. Troubleshooting
3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Cadac 182F - 2 COOK Supreme wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Cadac 182F - 2 COOK Supreme

Cadac 182F - 2 COOK Supreme Bedienungsanleitung - Deutsch - 6 seiten

Cadac 182F - 2 COOK Supreme Bedienungsanleitung - Holländisch - 7 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info