Bedienungsanleitung Cadac 8404 - LEISURE CHEF (Seite 5 von 11) (Englisch)

684186

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

6. Caring For The Grill Plates



The Non-stick reversible grill plate is coated with a tough durable non-stick coating that has been

used with great success on some of the best cookware in the world. Nevertheless, taking care of

it can help you to enjoy extra years of healthy, easy, non-stick cooking.

Use only low or medium heat settings to help retain the valuable nutrients in the food and

maintain the non-stick surface.

Whilst the non-stick coating is very durable, it can easily be damaged by the use of metal

cooking utensils. It is therefore recommended that only plastic or wooden utensils be used when

cooking.

Do not overheat the Non-stick reversible grill plate and always add a little cooking oil to the

surface before use.

The non-stick coating is perfectly safe in the dishwasher, but the non-stick surface is so easy to

clean that a quick hand-wash does the trick. The use of abrasive detergents is not

recommended, as this will permanently damage the non-stick surface.

After cleaning recondition the surface with a light wipe of oil.

Always allow the Non-stick reversible grill plate to cool before immersing it in water.

7. General Maintenance

8. Cleaning

After cooking, leave the burner on low with soapy water in the cooking dish to

soften cooking residue. When satisfied that excess fat has been removed, wash the Skottel BBQ

in warm water using a suitable non-abrasive detergent. Do not use sharp metal objects or

abrasive detergents on the vitreous enamel coated surface.

Remove the fat from the moat at the bottom of the Fat Pan (B) and clean as described for

the Skottel BBQ. Wash the Wire Grid and Deflector Plate in warm water with non-abrasive

detergent after wiping off any excess fat left after cooking.

: Wash the BBQ Lid in warm water using a suitable non-abrasive detergent. Do not use

sharp metal objects or abrasive detergents, as this will damage the surface coating.

For stubborn stains, oven cleaner may be used.

Skottel BBQ:

BBQ:

BBQ Lid

Note:



9. Storage



Handle the appliance with care. Do not drop it.

After use, wait until the appliance has cooled down, disconnect it from the gas cylinder and store

it in a cool dry place away from heat.

Keep the lid closed when not in use as this will prevent dirt and insects falling into the unit, which

may affect the gas flow.

Use a CADAC BBQ cover, especially if the unit is stored outdoors.



This appliance does not require scheduled maintenance.

Your Leisure Chef is fitted with a specific size jet to regulate the correct flow of gas.

Should the hole in the Jet become blocked, this may result in a small flame or no flame at all.

Do not attempt to clean the Jet with a pin or other such device as this may damage the

orifice (hole), which could make the appliance unsafe.

To replace the Jet: Unscrew the fitting connected to the inlet of the valve before unscrewing the

valve covers. that because the valve inlet has a left-hand thread, unscrewing any

fitting requires clockwise rotation when viewed from the fitting end of the valve.

Start by unclipping the plastic indicator from the control knob. This will expose a screw that

needs to be removed with a star screw driver. Once the screw has been fully unscrewed and

removed, you can pull the control knob off the valve spindle (see fig. 7a and b).

Using a star screw driver, undo and remove the 3 screws holding the front and bottom valve

covers in place (see fig. 7c).

Remove the front cover by unclipping it from the bottom cover and pulling it off the valve

spindle (see fig. 7d).

Turn the burner pan over so that the bottom valve cover face up. Unscrew the 2 fixing screws

and lift the bottom cover from the burner pan, this will expose the valve (see fig. 7e).

Undo the 2 screws holding the valve and place and carefully lift the valve out of the valve

box. Be carefull not to damage the piezo ignition wire (see fig. 7f and g).

With the valve in hand, use a suitable size spanner to loosen and remove the jet. Screw the

new jet into the valve, being carefull not to overtighten the jet, as this may damage the jet.

Do not use pliers to remove the old jet, or fit the new jet, as this may damage the hexagon

head, making it unusable and / or difficult to remove.

Reverse the above procedure to re-assemble the unit

Reconnect the gas supply as described in the Assembly Instructions.

The fitting of a hose is described in Section 12 - Assembly of the Appliance.

Replacing a Blocked Jet:

Replacing the Hose:

(see fig. 7a-g)

Remember

Fig. 7a

Fig. 7c

Fig. 7d

Fig. 7e

Fig. 7f

Fig. 7g

Fig. 7b

Unscrew

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cadac 8404 - LEISURE CHEF Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cadac 8404 - LEISURE CHEF

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info