Bedienungsanleitung Cadel Lean3 Plus (Seite 29 von 48) (Englisch)

694402

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

WALL

PLUS - LEAN

PLUS - MOON - TILE

PLUS

j - Components Test

To activate the “Components Test” function (only when the boiler is switched off) act as follows:

• Press the “menu” button.

• Scroll to “Settings” using the arrows

• Press “menu” to conrm.

• Scroll to “Components Test” using the arrows.

• Press “menu” to conrm.

• Select the test to be performed with the + - keys

• Press “menu” to conrm and “esc” to exit

k - “Chimney Sweep Function"

To activate the “Chimney Sweep Function” function act as follows:

• Press the “menu” button.

• Scroll to “Settings” using the arrows

• Press “menu” to conrm.

• Scroll to the “Chimney Sweep Function” function using the arrows.

• Press “menu” to conrm.

• Select “On” with the + - keys (Off by default)

• Press “menu” to conrm and “esc” to exit

l - Technical Menu

To access the technical menu one must contact an assistance centre as one needs a password to enter.

To intervene on the “Technical Menu” act as follows:

• Press the “menu” button.

• Scroll to “Settings” using the arrows

• Press “menu” to conrm.

• Scroll to “Technical Menu” using the arrows.

• Press “menu” to conrm.

• Select “Product Type”, “Service”, “Status Memory”, “Parameters” with the + - keys.

• Press “menu” to conrm and “esc” to exit

12.6 INFO MENU

• Product Type

• Firmware Version

• Software info

• Total hrs.

• Ignition N.

• Rpm Smoke Fan

• Smoke Temp.

• Air Fan Voltage

• Screw Loading

• Fire

12.7 START UP

We remind you that the rst ignition must be carried out by a specialized and authorixed technician who will

check that all is installed in compliance with current regulations and checks the efciency.

• If inside the combustion chamber there are booklets, manuals, etc..., remove them.

• Check if the door is correctly closed.

• Check if the stove is correctly inserted in the electric socket.

• Before switching the stove on, assure you the burning pot is clean.

• To start the stove, keep the P1 button pressed until the ON sign and a ashing ame to its side appear. The

ignition resistance pre-heating starts. After some seconds the feed screw loads pellets and the resistance pre-

heating continues. When the temperature is high enough (after about 5-8 minutes), ignition is considered to

be completed.

• Once the ignition step is complete, the stove moves into operating mode and shows the selected heat

output, the ambient temperature and the big ame (see Fig. 53 page 29).

• If the ambient temperature value exceeds the limit set on the button panel in the temperature set, the heat

output is brought to its lowest value and the small ame is shown (see Fig. 54 page 29). When the ambient

temperature decreases below the set temperature, the stove goes back to the set output.

Fig. 53 - Big ame Fig. 54 - Small ame

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cadel Lean3 Plus Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cadel Lean3 Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info