Bedienungsanleitung Caldera Paradise - serie 2021 (Seite 9 von 44) (Englisch)

784915

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Page 6 Getting Started

WATERFALL VALVE

The SALINA, MAKENA, MARTINIQUE,

SEYCHELLES & REUNION spas are equipped

with a cascading waterfall feature. It is activated by

pressing the "JETS" button and turning the valve

located on the front interior wall counterclockwise.

The flow is regulated by turning the waterfall valve

to the desired position.

AIR CONTROLS

Each jet system has its own air

control. These allow you to change

the power of the jets by regulating the

amount of air that is mixed with the

water coming out of the jets.

QUICK START-UP INSTRUCTIONS

BEFORE YOU FILL YOUR SPA

Make sure your spa has been properly installed per all local codes, this

includes the location of the spa, the foundation of the spa as well as

the electrical installation of the spa. Installation instructions in the form

of a Pre-Delivery Instruction booklet can be obtained from either your

CALDERA dealer or online.

DO:

• Know which water treatment system you will be using and make sure

you have necessary chemicals available. Read all of the instructions

that come with the system.

• Have FRESHWATER 5-way Test Strips Available.

• Have FRESHWATER Salt Test Strips Available if using the Salt system.

• Have pH/Alkalinity Up & Down available.

• Know the "Hardness" of your water, contact your dealer to help you

with this information. See Water Quality and Maintenance for more

information.

IMPORTANT: The spa can be filled with “softened” water as long as

the calcium hardness parameters (pg. 2) are maintained.

• Purchase the Clean Screen™ pre-filter to remove unwanted

contaminants from the tap water. This is recommended, not required.

DON'T:

• Power up the spa until it has been filled with water! Power to the

spa automatically activates critical components within the spa, such

as controls, heater, circulation pump, and other systems. If power

is supplied to these components prior to the spa being filled, the

components will be damaged, and this may result in a non-warranty

component failure.

• Fill the spa with hot water or cold water with the cold water temperature

below 10º C (50º F)! Tripping of the high-limit thermostat may result

causing your spa to stop functioning.

START-UP

Your CALDERA spa has been thoroughly tested during the

manufacturing process to ensure reliability and long-term customer

satisfaction. A small amount of water may have remained in the

plumbing after testing and, as a result, may have spotted the spa shell

or the spa siding prior to delivery. Before filling the spa, wipe the spa

shell clean with a soft rag. The following instructions must be read and

followed exactly to ensure a successful start-up or refill.

CAUTIONS

• Do NOT fill the spa with hot water, as tripping of the high-limit

thermostat may result.

• DO NOT CONNECT POWER TO AN EMPTY SPA. Power to the

spa automatically activates critical components within the spa, such

as controls, heater, and other systems. If power is supplied to these

components prior to the spa being filled, the components will be

damaged, and this may result in a non-warranty component failure.

• DO NOT use your spa after filling until all of the steps listed below are

completed.

• DO NOT add chlorine if treating your spa with polyhexamethylene

biguanide (Biguanide, PHMB, eg. BaquaSpa

®) sanitizer.

• Before filling your spa for the first time, remove the equipment

compartment door and check to ensure that the unions on either side

of the pump(s) and heater are hand-tight.

Door Panel Removal - see inside back cover:

a. Remove the 2 screws on the bottom of each corner.

b. Find notches in bottom of panel, place fingers on one side

and center notch. Slightly pull on bottom side panel to release 1st

clip. Move over to other side and center notch and pull on bottom

to release 2nd clip, then lower and remove panel.

1. CLOSE DRAIN, remove the filter compartment cover, skimmer

basket, weir, and filter. Fill your spa through the filter compartment

using the CLEANSCREEN pre-filter that attaches to your garden

hose. The water level of your spa should be maintained at a level

2.5 cm above the highest jet in the spa. Reinstall the filter and then

the skimmer basket, and weir once the spa is filled.

2. AFTER THE SPA HAS BEEN FILLED with water and the

equipment compartment door is secured, power must be applied

to the spa.

• FIRST activate power to the subpanel from the main house

panel.

• NEXT open the door of the electrical subpanel and reset the RCD

breaker.

• FINALLY, close and secure the subpanel door.

3. TO CHECK THE OPERATION OF THE JET SYSTEM and to

purge any remaining air from the heating system complete the

following steps:

• Press the soft button next to Jet Max to place both jet pumps on

High.

• Once the jet system is fully operational (as indicated by strong,

non-surging jets), priming of the spa is complete

• To turn off the jets, press

the soft button next to All Off on the

home screen

to turn all functions off simultaneously

• If you do not feel a steady stream of water from your jets,

refer to the instructions for priming the pump in the SPA

TROUBLESHOOTING section.

IMPORTANT: Be sure that the diverter is in the middle position.

Caldera Paradise - serie 2021 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Caldera Paradise - serie 2021

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info