Bedienungsanleitung Caldera Paradise - serie 2021 (Seite 10 von 44) (Englisch)

784915

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Page 7

Getting Started

4. SET THE TEMPERATURE CONTROL to the desired temperature

between 38°C (100°F) and 40°C (104°F), then place the spa

cover on the spa and allow the water temperature to stabilize

(approximately 24 hours). Make sure you secure the cover in place

using the cover locks. Periodically check the spa water temperature.

When the water temperature climbs above 32°C (90°F), proceed

to the next step. The spa temperature is pre-programmed to reach

38°C (100°F), and will normally do so within 18 to 24 hours. You may

change the water temperature by pressing the OPTION hard button

then press the soft button next to Temperature, (press soft button

next to



on the control panel to raise the temperature, or lower

temperature by pressing soft button next to ▼). After a few hours,

the water temperature will remain within 1.5°C (3°F ) of your selected

temperature.

5. USING A TEST STRIP AND APPLICABLE CHEMICALS adjust

Total Alkalinity (TA) to 80 ppm, Calcium Hardness (CH) between

75 - 150 ppm (if using Salt System between 25 - 75 ppm), then

spa water pH to between 7.4 and 7.8. These procedures are listed in

the “Water Quality and Maintenance” section.

OPERATION NOTE: Adjusting the Total Alkalinity as the first step is

important, as out-of balance TA will affect your ability to adjust the pH

correctly and will prevent the sanitizer from operating effectively.

When using the FRESHWATER Salt system the Calcium Hardness

must be between 25 - 75 ppm, if hardness is above 75 ppm use

VANISHING ACT (see pg. 11).

IMPORTANT: Activate the Clean cycle (Press the soft button next

to CLEAN on the home screen) before adding spa water chemicals

directly into the filter compartment. Make sure all diverter valves are

set to the middle position.

6. SUPERCHLORINATE THE SPA WATER by adding 1½ teaspoons

of FRESHWATER chlorine (sodium dichlor) per 950 liters (250

gallons) of spa water, then activate the Clean cycle.

7. TEST THE SPA WATER FOR CHLORINE RESIDUAL. If the

residual is between 1 and 5 ppm on the test strips, go on to the next

step. If the residual is less than 1 ppm, activate the Clean cycle, and

then retest, add more chlorine as necessary.

WARNING: High sanitizer levels can cause discomfort to the user’s

eyes, lungs and skin. Always allow the sanitizer level to fall to the

recommended range before using the spa.

8. RECHECK the Total Alkalinity (TA) 40 - 120 ppm, Calcium

Hardness (CH) 75 - 150 ppm (25 - 75 ppm with salt), then spa water

pH between 7.2 and 7.8.

OPERATION NOTE: Make sure you adjust your Total Alkalinity and

pH correctly, this will affect

the sanitizers effectiveness.

The spa is ready for use when the spa water has circulated and

the chlorine level remains between 1 and 5 ppm.

OPERATION NOTE: For proper water circulation during the ten-minute

Clean cycle the following steps should be performed.

• Place the diverter valve in the middle (split flow) position

• Place air control levers in OFF position by rotating clockwise

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Caldera Paradise - serie 2021 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Caldera Paradise - serie 2021

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info