Bedienungsanleitung Caliber mcd 163 (Seite 8 von 18) (Englisch)

168721

Zoom out

Zoom in

Vorherige Seite

1/18

Nächste Seite

Switching on/off the unit

Switch on the unit by pressing any button

(except button and button) or inserting

a disc to disc slot.

When system is on, press the button to

turn off the unit.

Sound adjustment

- Rotate the volume knob on the head unit to

adjust volume level.

- Press the button to enter into the

audio selecting mode. Press this button

continually will change in the following

order:

SEL

When TP information gets lost at the

current station for retune time, the beep

sound is out-putted.

When newly tuned station has not RDS

signal, “PI SEEK” is suppressed somewhat.

Rotate the volume knob button to adjust the

desired sound quality.

-for2

seconds to enter into the menu mode

Press it continually, it is activated as

cyclical mode of following functions for

user's selection

Press and hold the button

Rotate the volume knob to select the

desired item.

SEL

TA SEEK/ALARM PI SOUND/MUTE RETUNE L/S

MASK DPI/ALL BEEP 2’ND/ALL/OFF

VOL BAS TRE BAL FAD

(Volume) (Bass) (Treble) (Balance) (Fader)

TA SEEK/ALARM

- TA SEEK mode:

- TA ALARM mode:

When newly tuned station does not

receive TP information for a few seconds,

the radio retunes to next station which has

not the same station (PI) as the last station,

but has the TP information.

When TP information gets lost at the

current station for retune time which is set

by RETUNE SHORT (30 sec.) or RETUNE

LONG (90 sec.), the radio start to retune to

next same PI station. When same PI station

does not catch in 1 cyclic search, the radio

retunes to next station with TP information.

When this mode is selected, any

automatic retune mode is not activated.

Only double beep sound (ALARM) is

output.

When newly tuned station does not have

TP information for several seconds, beeps

come out.

PI SOUND/MUTE

While AF switching is implemented in

C201 station, AF can switch to 100 MHz,

which is non genuine AF (where, different PI

with same AF) in short “DIP”.

If a car cruises that critical area back and

forth, an oscillation phenomenon can be

occurred, because the different PI code can

be received from 100 MHz with “XXX” PI.

The car radio has special procedure to

reduce even this kind of unavoidable

situation however there is a limit to be

escaped from this serious case perfectly.

In that serious case, 2 modes are

selectable as follows:

The AF frequency (which has different PI

or NO RDS signal with high field strength) is

masked during checking PI when the unit

-PISOUNDmode:

-PIMUTEmode:

- RETUNE L mode:

- RETUNE S mode:

When above different PI sound (DIP) is

heard once in a while, the Dip's sound will

be heard for a short time.

Under above same situation, a mute

sound will be heard for a short time.

The initial time of automatic TA search or

PI search modes is selected.

When PI information is not caught for

retune time, the radio starts to retune to

next same PI station.

When same PI station does not catch 1

cyclic search, the radio goes to last station

and waits for several minutes until PI code

is received.

Selected as 90 seconds.

Selected as 30 seconds.

RETUNE L/S

MASK DPI /ALL

General Operations

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Caliber mcd 163 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Caliber mcd 163

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info