Bedienungsanleitung Caliber PARK 300 (Seite 4 von 11) (Englisch, Holländisch, Französisch)

781508

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

ENGLISH

ALARM MODE

FRONT DETECTION

REAR DETECTION

INSTALLATION STEPS

1. Choose right installation position for sensors

2. Select drilling position for sensor A and D (select drilling position for sensor 1 and 4)

3. Select drilling position for sensor B and C (select drilling position for sensor 2 and 3)

4. Locate the position and drill

5. Install the sensors and hide wires

6. Install the display

7. Install the control box

8. Connect the whole system according to the general installation diagram

INSTALLATION AND TEST

1.Adjust the directions of the sensors and axial orientation, neaten the wiring after

installing the sensors.

2. Connect the power supply of back control box to the reversing light. Connect the

power supply of front control box to auto ignition switch.

3. Connect the data wires between the front control box and the display, and connect the

control switch with front control box. Do not have the sensors connected at that

moment.

4.When the car is started, the horn sounds “DangDang” to enter into working status, 2s

later, it turns to standby status. Put the car into back reverse, then the display shows “En”

(n=0, 1, 2•••) to show the number of defective sensors, with the indication of exact

defective sensors. Insert one of the sensors into corresponding interface in front/back

control box. Human being could be detected normally, if he stands within 0.7m right

before the sensor; pull out the sensor, and check other sensors in the same method.

Insert all the sensors in corresponding interface after testing.

Test: A.After connecting a sensor with the control box, if the buzzer sounds “Bi•••••••••”

,please check whether there is any obstacle around it, or the sensor is fixed too

tight or close to great interference sources (such as vent-pipe, wires).

B.If the display shows any distance figure with no obstacle around the sensor, the

sensor may detect the ground or some outshoots of the car (such as registration

mark, etc.), please check the directions of sensor and axes.

C.If the system still could not work properly after the above mentioned handling,

the sensor(s) can be deemd defective, or unmatch with the control box.The system

should be replaced.

Note: A.The connection between sensor and the digital control box in unique.

B.It performs as: when detecting within 0.3m, it shows “0.0”, instead of 0.1-0.2 to

alert which requires the driver to stop immediately.

NOTE

1.The car must be in power-off, when installing ultrasonic sensors

2. It’s performance may be affected in following situation: heavy rain, gravel road, bumpy

road, sloping road and bush, very cold , hot or moist weather, or the sensors is firned or

iced over.

3. Switches among ultrasonic electric wave, DC and AC and those among 24V, 12V voltages

may also effects its performance.

4.The sensors should be installed appropriate loose or tight

5. It’s performance will be effected if the sensors are fixed on metallic bumper.

6.Avoid installing the digital control box in places of great interference, such as vent-pipe,

wiring nearby.

7.Test the system to make sure it works normally before using.

8.This system is a reversing aid and the manufacturer will take no responsibility for any

accidents caused after the kit is installed.

GENERAL INSTALLATION DIAGRAM

STAGE DISTANCE AWARENESS ALARM SOUND DIGITAL DISPLAY ALARM COLOR

1>0.7m Safety area

Safety area

Alarm area

Danger area

0.3m 0.3

0.0

<0.3m

0.6~0.7m 0.6~0.7 Green

Yellow

Red

0.4~0.5m 0.4~0.5

Silence

Ding Ding Ding

Ding

Ding Ding Ding

STAGE DISTANCE AWARENESS ALARM SOUND DIGITAL DISPLAY ALARM COLOR

Safety area

Alarm area

Danger area

0.3

0.0

Green

Yellow

Red

>1.5m

0.3m

<0.3m

1.5~1.1m

1.0~0.4m

1.5~1.1

1.0~0.4

Silence

Dang Dang

Dang Dang Dang

Dang

Black wire - earth

Red wire + 12V (ON/ACC)

Red wire +reversing light

Black wire -reversing light

BACK

FRONT

WORKING CONDITIONS

1.When the car is in reverse, 8 sensors work at the same time.The distance from

the nearest obstrucion and the bumper will be shown on the display with horn

alarming and direction indicator.

2.When driving forward only the front sensors work.

There are three options to control the front sensors:

a. Control by switch (this is recommended):

yellow wire of front control box - switch - ON/ACC

When switch is on, the front sensors start to work..

b. Control by braking:

yellow wire of front control box - braking signal

When braking the front sensors start to work; when stopping with braking the

sensors will stop working in 30 sec.

c. Control by both switch and braking:

yellow wire of front control box - switch - braking signal

When the switch is on, sensors will start to work as above mentioned option b.

PARK 300 manual werkdoc.qxd 28-11-2007 08:46 Pagina 6

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Caliber PARK 300 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info