Bedienungsanleitung Cambridge Audio AXA35 (Seite 6 von 10) (Englisch)

699770

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

Front panel controls

POWER BUTTON

Switches the unit between Standby mode (indicated by dim LED) and On (indicated

by bright LED). Standby mode is a low power mode where the power consumption

is less than 0.5 Watts.

This product has APD (Auto Power Down) enabled as default. After inactivity of 20

minutes, the product will automatically switch to Standby.

Auto Power Down (APD)

You can enable and disable the units APD setting. This can be adjusted by pressing

and holding the Power button until the LED ashes in sequence.

The two options below show which option is selected.

Standby ashes 5 times - APD disabled

Standby ashes 10 times - APD enabled

Note: Make sure the unit is On, before making changes to the APD function.

HEADPHONES SOCKET

This connection allows for the connection of stereo headphones with a ⁄ inch

jack plug. Headphones with an impedance of between 32 and 600 ohms are

recommended.

Note: Connecting headphones will automatically mute the loudspeaker outputs.

INFRARED SENSOR

Receives IR commands from the supplied remote control.

An unobstructed line of sight between the remote control and the sensor is

required.

AUX IN

This source input allows you to connect a portable audio device such as an MP3

player or streaming device directly into the front of the unit using a 3.5mm stereo

Aux lead.

Once plugged in, this input is automatically selected, although other inputs apart

from A1 can still be selected once a stereo-jack is plugged in. The A1/AUX button on

the front of the unit will select this input whilst a stereo-jack is plugged in.

Note:

– Plugging a source into the front panel Aux input overrides the A1 input. Simply

remove the jack from the front panel to automatically re-enable the A1 input.

– Also note that as the output level of Aux players tends to be quite low, the AXA35

adds 10dB to the current volume setting when (and only when) the Aux input is

selected.

A2 A3 MENUA1 / AUX

AUX IN

VOLUME

A35AX

PHONOA4

INPUT SOURCE BUTTONS

(A1/AUX,A2, A3, A4,PHONO)

Press the relevant source button to select the desired input source.

DISPLAY

Used to display information such as the selected input source, volume and tone/

balance levels.

Note: When rst purchased, the display will have a protective lm over the top. Peel

this o for a clear display.

MENU BUTTON

Pressing this once will select the Bass option. Pressing a second time will select the

Treble option and pressing a third time will select the Balance option. When one

of these options is selected, the volume control will adjust the level. If nothing is

pressed for a while, the source will be displayed and the volume control will go back

to controlling the volume level.

VOLUME CONTROL

Use to increase or decrease the level of the sound from the outputs of the unit. This

controls the volume level of the loudspeakers and headphones. The volume control

will also change the level of bass, treble and balance in the menu options.

Note: It does not aect the level of the ‘Rec Out’ output as this has a xed level.

1 2 3 4 5

7 8

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cambridge Audio AXA35 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cambridge Audio AXA35

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info