Bedienungsanleitung Cambridge Audio azur 540d v2 (Seite 15 von 20) (Englisch)

137148

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

540D V2azur

Dolby Digital Setup menus

When the Dolby Digital setup menu is selected, use the and 

arrows to move to the desired menu. Use the Navigation arrows

() to adjust the settings and press the Enter button to confirm

your selection.

Dynamic

Dolby Digital encoded discs allow for the dynamic range (the difference

between loud and quiet passages) to be compressed (i.e. for late night

listening). The options are:

Full, 7/8, 3/4, 5/8, 1/2, 3/8, 1/4, 1/8, Off

When ‘Full’ is selected, the peak-to-peak value of the audio signal is

compressed by the maximum amount. When ‘Off’ is selected, no

compression is applied.

Channel Delay

For the best surround-sound effect, it is desirable to adjust the channel

delay so that sounds from each speaker arrive at the listener at the

same time. This is done by measuring the distance from the listening

position to the Left or Right Front speaker (which should be equidistant

from the listener), the distance from the listening position to the Centre

Speaker and similarly to the Right Rear Speaker, Left Rear Speaker and

Subwoofer. The diagram below illustrates this:

Precise measurements are not critical (approximately a foot or 30cm is

fine) and do not worry if your front speakers are slightly asymmetric.

The channel delay to be entered for each speaker is then the difference

between the distance to the Front Speakers and the speaker to be

configured.

As an example, if the Front Speakers are 5½ft from the listener and the

Centre Speaker is 3ft from the listener, the channel delay to be entered

for the Centre Speaker is 2½ft. Similarly, if the Right Rear Surround is

3½ft from the listener, the channel delay would be 2ft.

Note: The distance between the surround speakers and the listener

must be shorter than or equal to that between the front speakers and

the listener.

The measurements are in feet for units sold in North America or Canada

and in metres for units sold in Europe or Australasia.

Use  to select each speaker in turn and  to enter a distance

value.

In this way, the 540D V2 calculates and uses the correct delay time for

each channel so that each channel reaches the listener simultaneously.

Go To Dolby Digital Setup

-- Dolby Digital Setup --

Dynamic

Channel Delay

HDMI Audio

Two options are available: PCM Stereo and Follow SPDIF.

When HDMI Audio is set to ‘PCM Stereo’, the HDMI output will be

16/44.1 for CDs and, depending on the soundtrack bit depth, 16/48 or

16/96 stereo/stereo downmix for DVD.

When the 540D V2 is connected directly to a TV set which can receive

Stereo Audio over HDMI, PCM Stereo is the best setting to use. Your TV

set will then always receive a two-channel downmix from CDs or DVDs.

When HDMI Audio is set to ‘Follow SPDIF’, the HDMI output will follow

exactly the SPDIF output as per the previous section and table.

When the 540D V2 is connected to an AV receiver by HDMI, there are

two possibilities depending on whether the receiver accepts HDMI audio

directly or switches HDMI video and uses SPDIF for digtial audio

reception:

1. For AV receivers that can receive HDMI audio, set the HDMI Output to

‘Follow SPDIF’. Now set the SPDIF Output to ‘Raw/Bitstream’. The AV

receiver can now decode the bitstream over HDMI into the formats it

supports. The TV itself will then not receive any audio (unless the

receiver has the capability of making a stereo downmix and

outputting it over HDMI).

2. For AV receivers that switch HDMI and use SPDIF for audio reception

(such as our Azur 540R V3 and 640R), set the HDMI output to ‘PCM

Stereo’ and set SPDIF Output to ‘Raw/Bitstream’. The AV receiver now

receives and decodes surround-sound via the SPDIF connection. The

TV will always also receive a two-channel downmix directly from the

DVD player over HDMI which can be used if desired.

Pro Logic II

The 540D V2 can decode Stereo soundtracks (that have been suitably

encoded) into five-channel surround-sound using Dolby Pro Logic II.

Two modes are available (Music and Movie) and are optimised for the

different programme types.

To use Pro Logic II, turn it on and then select either Movie or Music mode

depending on the programme type.

Note: Enabling Pro Logic II decoding disables Dolby Digital decoding (Pro

Logic is used instead).

1 = Front Left & Right speakers

2 = Centre speaker

3 = Surround Left speaker

4 = Surround Right speaker

5 = Subwoofer

ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cambridge Audio azur 540d v2 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cambridge Audio azur 540d v2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info