Bedienungsanleitung Cambridge Audio Stream Magic 6 V2 (Seite 17 von 20) (Englisch)

656763

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

ENGLISH

Balance control

Balance control allows the sound to be panned slightly to the left or the right and

is sometimes used to compensate for channel imbalance found with recordings

transferred from vinyl records etc. or to compensate for offset loudspeaker

positions relative to the listener.

Balance is only available if Digital Pre-Amp mode (described above) is enabled.

The function can be found in the menu under: to “Settings -> Advanced -> Balance”

(only when Digital Pre-Amp is enabled)

The last used balance setting is memorised when the unit powered off.

USB Audio Class

USB Class options enable Stream Magic 6 compatibility with both USB Audio 1.0

and USB Audio 2.0 interface formats. The default setting is USB Audio 1.0 which

will work driverlessly with most operating systems for 16-24 bit content at 32-

96kHz. Note USB Audio 2.0 requires a driver to be loaded for Windows. Without

this selecting USB Audio 2.0 will normally give no output. See earlier section on

USB Audio for advanced users.

Remote Code

There are two Options:

Option 1 – is the default and works with the Stream Magic 6 remote control when

also in its default mode.

Option 2 – gives a secondary code set in cases where the remote codes are found

to clash with another remote handset.

If Option 2 is selected on the Stream Magic 6 then the remote handset must also

be set to Option 2 remote codes as well as follows:

Press and hold down the

button whilst inserting the batteries to switch to

Option 2.

By inserting the batteries without the

button held down will default to Option1.

Language

Allows you to change the display language used.

A list of the currently supported languages will be shown. Select your preferred one

and press enter.

Note: The Stream Magic 6 will then restart in order to start again in the new

language, this will take approximately 30 seconds.

Idle Mode

Idle mode, when enabled, allows Stream Magic 6 to enter a lower power

suspended state using the Standby/On button. The display is turned off and many

of the internal processes and circuits are disabled to reduce power consumption.

However the difference between Idle and Standby is that in Idle mode, power

remains connected to the main controller, Ethernet and Wi-Fi sections.

In Idle mode, networking functionality remains alive in the background. This means

that Stream Magic 6 can be quickly woken up out of the suspended state into

an operational state using not only the front panel, the infra-red remote and the

control bus, but also the iOS app running on the iPhone or iPad. This is not possible

when the unit is in full Standby mode.

To enable Idle mode using the Standby/On button, it must rst be activated within

the setup menus. Go to “Settings -> Advanced -> Idle Mode” and set to “On”.

Short presses of the Standby/On button then toggle between On and Idle modes.

Note: after putting the unit into Idle mode, you will not be able to wake the unit into

full On mode until 5 seconds have elapsed.

Full low power standby can still be activated by keeping the Standby/On button

pressed for more than two seconds. A subsequent press of Standby/On turns the

unit fully on, but remember that this can’t be done over the network (i.e. from the

iOS app) and that it takes longer to reach the full operational state.

Upgrade Firmware

Use this option to download new rmware for the Stream Magic 6 from Cambridge

Audio over the Internet.

If you select this item the Stream Magic 6 will contact our server and see if a

newer version of software is available (‘Checking for updates’ will be shown in the

display).

If new software is found the Stream Magic 6 will prompt you and ask if you want

to download it or not. It is a good idea to update the rmware from time to time to

take advantage of any bug xes or new features. At this stage, you can press the

Stream Magic 6’s

button to cancel the rmware upgrade. A Firmware upgrade

may take several minutes.

Note:

– It is very important that once the Firmware upgrade has started you do not

switch off the power to the Stream Magic 6 until the operation is complete

otherwise the Stream Magic 6 may become permanently damaged.

– Also do not interrupt the network or internet connection by removing the

Ethernet lead or switching off your router etc.

Stream Magic 6 Name

This menu allows the setting of the declared UPnP Client name for your Stream

Magic 6.

This is the name other UPnP devices (such as control points and remote Apps etc.)

will display when they see the Stream Magic 6.

The default name will be ‘Stream Magic 6’ but can be changed to any name you

can easily recall such as ‘Dads Stream Magic 6’ or ‘Kitchen’ etc.

Advanced

This menu contains advanced setup/conguration as shown below.

Advanced

Digital Pre-amp Mode

Balance

(only available if Digital Pre-amp mode is enabled)

USB Audio Class

Remote Code

Language

Idle Mode

Automatic Power-down

Edit Digital Input Names

Digital Pre-Amp Mode

Digital Pre-amp mode, when enabled, allows volume adjustment to be performed

within the up-sampling Digital Signal Processor (DSP) before being converted to an

analogue audio signal for connection to a power amp.

Normally, the output of Stream Magic 6 (and most other source components) is

output at “full-scale” (i.e. maximum volume). This signal is then fed into a pre-amp

which is used to control the volume of all audio sources connected to it.

To enable Digital Pre-Amp mode it must rst be activated within the setup menus.

Go to “Settings -> Advanced -> Digital Pre-amp Mode” and set to “On”. Stream

Magic 6 will then respond to the vol+ and vol- buttons on the remote control at

any time.

It is also possible to adjust the volume using the rotary controller knob on the front

of the unit.

Whenever the StreamMagic 6 is showing its ‘Now playing’ screen turning the rotary

controller knob will adjust the volume. Pressing back or home etc. to access the

menu system allows the use of the rotary controller for menu browsing. If you are

in a menu and need to adjust the volume immediately simply press the ‘i’ button to

go straight to ‘Now playing’ and then use the rotary controller.

Maximum volume is shown as “0dB” on the display. Reductions in volume away

from maximum are shown in the form of negative numbers i.e. “-12dB”. The larger

the negative number, the larger the signal reduction so the quieter it will be. A

muted or silent output is shown as “MUTE”. The volume screen is shown briey

when the volume is changed, after which it times-out to the previously displayed

screen.

The last used volume setting is memorised when the unit powered off.

Cambridge Audio Stream Magic 6 V2 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cambridge Audio Stream Magic 6 V2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info