Bedienungsanleitung Cami New Askir 30 (Seite 5 von 8) (Englisch)

667800

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

www.medicalsuction.co.uk

ACCESSORIES SUPPLIED

DESCRIPTION

COMPLETE ASPIRATION JAR 1000cc

CONICAL FITTING

TUBES SET 6 mm x 10 mm

ASPIRATION PROBE CH20

ANTIBACTERIAL FILTER

Antibacterial Filter: The filter is produced with (PTFE) hydrophobic material witch prevents fluids entering the pneumatic circuit.

The filter is for a single patient use which will protect patients and machines from cross contamination.

When the filter is wet, it’s not possible to use the unit therefore the filter should be changed immediately.

In case of possible contamination or discolouration, change the filter immediately.

Don’t use the suction unit without the protection filter fitted.

Suction catheter: Single-use device to be used on a single patient. Do not wash or re-sterilize after use. Reuse may cause cross-

infections.

Don’t use after lapse of the sell-by date

WARNING: Suction tubes for insertion in the human body purchased separately from the machine should comply with ISO

10993-1 standards on material biocompatibility.

Aspiration jar: The mechanical resistance of the component is guaranteed up to 30 cycles of cleaning and sterilization. Beyond this

limit, the physical-chemical characteristics of the plastic material may show signs of decay. Therefore, we recommend that you to

change it.

Silicone tubes: the number of cycles of sterilization and/or cleaning is strictly linked to the employment of the said tube. Therefore, after

each cleaning cycle, it is up to the final user to verify whether the tube is suitable for reuse. The component must be replaced if there

are visible signs of decay of the material constituting the said component.

Conical fitting: the number of cycles of sterilization and the number of cleaning cycles is strictly linked to the employment of the said

component. Therefore, after each cleaning cycle, it is up to the final user to verify whether the fitting is suitable for reuse.

The component must be replaced if there are visible signs of decay in the material constituting the said component.

Service life of the device: More than 850 hours of operation (or 3 years) in accordance with the standard conditions of testing and

operation. Shelf life: maximum 5 years from the date of manufacture.

CLEANING OF ACCESSORIES

To clean the plastic housing of the device wear disposable latex gloves and clean with denaturated alcohol or hypoclorite solutions.

Washing and / or cleaning the autoclavable jar as to be carried out as follows:

 Wear protection gloves and apron (glasses and face mask if necessary) to avoid contact with contaminating substances;

 Disconnect the jar from the device

 Disconnect all tubes from the jar and the protection filter

 Empty and dispose of the content and of the suction catheter according to the laws in force in your country;



Separate all parts of the cover (overflow valve, o-ring);

After disposing of disposable parts and disassembling the jar wash in running cold water and rinse thoroughly.

Then soak in warm water (temperature shall not exceed 60°C).

Wash thoroughly and if necessary use a non-abrasive brush to remove incrustations.

Rinse in running warm water and dry all parts with a soft cloth (non-abrasive).

The jar and the cover can be autoclaved by placing the parts into the autoclave and running one sterilization stem cycle at 121°C

(1 bar relative pressure) making sure that the jar is positioned upside down.

Mechanical resistance of the jar is guaranteed up to 30 cycles of sterilization and cleaning at the indicated conditions

(EN ISO 10079-1). Beyond this limit the physical-mechanical characteristics of the plastic may decrease and replacement of the part is

therefore recommended.

After sterilization and cooling at environment temperature of the parts make sure that these are not damaged.

Assemble the jar as follows:



Place the overflow valve into its seat in the cover (under VACUUM connector)

 Insert floating valve keeping the o-ring towards the opening of the cage



Place the o-ring into its seat around the cover

 After completing assembling operations always make sue that cover seals perfectly to avoid vacuum leakages or liquid exit

The aspiration tubes can be sterilized on autoclave using a sterilization cycle at 120°C.

The conical connector can be sterilized on autoclave using a sterilization cycle at 121°C.

The device is ready for a new employment now.

DO NOT WASH, STERILIZE OR PUT IN AUTOCLAVE THE ANTIBACTERIAL FILTER

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cami New Askir 30 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info