Bedienungsanleitung Cami New Askir 30 (Seite 6 von 8) (Englisch)

667800

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

www.medicalsuction.co.uk

MAINTENANCE

The NEW ASKIR 30 12V suction equipment does not need maintenance or lubrication.

It is, however, necessary to inspect the unit before each use. With regard to training, given the information contained in the user manual

and since it is easy to understand the said device, it doesn’t appear to be necessary.

Unpack the instrument and always check integrity of plastic parts and feeding cable, they might have been damaged during previous

use. Connect the cable to electrical network and turn the switch on.

Close the aspirator outlet with your finger and with suction regulator at maximum check that the vacuum indicators reaches at least -

75kPa (-0.75 bar). Rotate the knob from right to left. The vacuum indicator should go down -25kPa (-0.25 bar).

Check that no loud noises are present. The device is protected by a safety fuse (F 10A L 250V) situated in the cigarette lighter adapter.

For fuses replacing, always the type and the range.

Before changing the fuse, disconnect the plug from the power supply socket.

Fault type Cause Solution

1.The suction unit doesn’t work

Cable is damaged

External power source failure

Replace the cable

Check the external power source

2.No aspiration

Jar Cap badly screwed down Unscrewed the cap, then rescrew it correctly

3. No aspiration Lid seal not in its seat Unscrew the cap and insert the seal properly in its seat

4.The Vacuum power on the

patient side is either very low

or absent

a) Vacuum regulator set to minimum

b) Protection filter blocked or

damaged

c) Connection tubes blocked, kinked

or disconnected

d) Shut-off valve blocked or

damaged

e) Pump motor damaged

a) Turn the vacuum regulator clockwise and check the

value of the vacuum on the gauge

b) Replace the filter

c) Replace or reconnect the tubes, check the jar

connections

d) Empty the jar, or disconnect the tube from the jar and

unblock the shut-off valve. The unit twill only work in the

upright position

e) Refer to authorised service personnel

5. The float doesn’t close If the cap has been washed, ensure

that the float is not partially detached

Insert the float into it’s place

6. The float doesn’t close The float it’s covered by dirty

material

Unscrewed the cap, leave the and put in on autoclave

7. Low suction Foam inside the jar Fill the jar to 1/3 full of ordinary water

Faults 1 - 2 - 3 - 4 - 5 - 6 - 7 None of the remedies has

achieved the desired results

Contact the seller or CA-MI After-sales Assistance

Service

If the overfill security system it’s activated, don’t proceede with the liquid aspiration.

If the overfill security system doesn’t work there are two cases:

1° case – If the overfill security system doesn’t work the aspiration will be stopped by the bacteriological filter who avoid the liquid

penetration inside the device.

2° case – If both the security system doesn’t work, there is the possibility that liquid comes inside the device, in this case return the

device to CA-MI technical service.

CA-MI Srl will provide upon request electric diagrams, components list, descriptions, setting instructions and any other information that

can help the technical assistance staff for product repair

BEFORE EVERY CHECKING OPERATION, IN CASE OF ANOMALIES OR BAD FUNCTIONING, PLEASE CONTACT CA-MI

TECHNICAL SERVICE. THE MANUFACTURER DOES NOT GIVE GUARANTEE IF INSTRUMENT, AFTER THE TECHNICAL

SERVICE CHECKING, APPEARS TO BE TAMPERED.

INSTRUCTIONS

 The device must be checked before each use in order to detect malfunctions and / or damage caused by transport and / or

storage.



The working position must be such as to allow one to reach the control panel and to have a good view of the empty indicator, the

jar and the antibacterial filter.



It is recommended not to keep the device in your hands and / or to avoid prolonged contact with the body of apparatus.

WARNING: For proper use, place the aspirator on a flat, stable surface in order to have the full volume of use of the jar and better

efficiency of the overflow device.



Place the unit on a flat, horizontal surface



Connect one end of the short silicon tube, with antibacterial filter, to the suction connector on the lid of the jar.

 The other tube already connected to the filter has to be connected to the “VACUUM” jar outlet, where has been fixed the red float

(security float). When the 90% of the volume of the jar is reached there is the activation of the security float (the float close the

aspiration connector on the jar) to avoid liquid penetration inside the device.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cami New Askir 30 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info