Bedienungsanleitung Camina-Schmid Profi W (Seite 10 von 16) (Englisch)

810681

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

7.4 Closed hot water circuit

with completely submerged 'Profi W' heating insert and

oil/gas boiler (central heating)

Punkt 7.1 Abb. 1

Connection example, depending on type

of local heating system

The Federal Immission Control Ordinance

(BImSchV) demands a minimum water volume

of 55 litres per kilowatt boiler output for central

solid fuel boilers.

* Rule of thumb for buffer tanks: 55 l/kW

(boiler kW output)

Gravity brake

(non-return valve)

Profi W

Cold water

Circulation

Hot water

radiator

Solar components:

- control unit

- expansion tank

- pump, etc.

Underfloor heating

Solar

Pressure

relief valve

Flow, 3/4"

Circulation

pump

Return boost

Cold water

inlet

Sensor for thermal discharge

safety device, 1/2"

Thermal discharge

safety device

Automatic

vent valve

Return, 3/4"

Drain, 1/2"

Return boost sensor

Expansion tank with

pressure gauge

Buffer storage*

min. 700 l

Domestic hot water tank

Domestic hot water

charging pump

Bypass

Stop cock

Expansion tank

with pressure

gauge

Pressure relief valve

Drain

Oil-fired

central heating boiler

www.schmid.st

8. 1 General information:

Correct functioning of the heating insert depends on the

size and quality of the flue. The flue must therefore be

inspected for these points in accordance with local

regulations before installing the heating system

(DIN 18160 Sh. 1, ask sweep for details).

All openings leading into the flue (including chimney

sweeping access doors and condensate drains) must

close tightly!

During hot water mode the heat contained in the fuel

gas is also required to heat the water (50 l/80 l water

volume). This keeps the flue gas temperature constantly

below 400° C (stove with reversing stone). This allows

direct connection to the flue.

A connection via the secondary heating surfaces is also

possible on this boiler stove.

Use the lateral connections for this (stove without reversing

stone), because the flue gas temperature is higher hereat

approx. 500° C, which will allow secondary heating to be

utilised.

For hot water and hot air mode (without heat-up flap),

see Point 8.2 Fig. 2.

For hot water or hot air mode (with heat-up heat-up flap),

see Point 8.2 Fig. 3.

8.2 Installation examples

Tile stove system for hot water mode only, without hot

air mode

Tile stove system for hot water and hot air modes, e.g.

with reheater box

Tile stove system for hot water or hot air mode, e.g.

with reheater box

8. Connecting to the flue

Point 8.2 Fig. 1

Fuel gas channel directly to the flue

Point 8.2 Fig. 2

Fuel gas channel lateral from the boiler

stove through the reheater box to the flue

Point 8.2 Fig. 3

Our recommendation:

Installation of a switch-over flap for varying the flue

gas channel directly to the flue or across the reheater

box.

Hot water mode - Fuel gas channel

directly to the flue

Hot air mode - direct fuel gas channel

closed, fuel gas channel through

reheater box to the flue

Punkt 8.2 Abb. 3

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Camina-Schmid Profi W Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Camina-Schmid Profi W

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info