Bedienungsanleitung Campingaz Base Camp (Seite 10 von 41) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

658614

Zoom out

Zoom in

Vorherige Seite

1/41

Nächste Seite

E - STORAGE - SERVICING

1) Stove

Ensure that your stove is regularly maintained, and it

will give you many years of excellent service.

- Do not clean the stove while it is in operation. Wait for

it to cool down, to avoid burning yourself on the hot

parts (pan supports, burners).

- When cleaning, be careful to avoid clogging the bur-

ner holes. If the holes are clogged, for example by

food that has spilled over, open them with a non-

metal brush.

- Clean greasy parts with soap and water or a non-

abrasive detergent product.

- The pan holder (2) can be removed. You can take it

off to make cleaning the device easier.

To remove the pan support, pull it upwards. To repo-

sition it, insert the legs located on each site of the

support into the holes found on each side of the

device (see figure 5).

- The lid may also be removed (Base Camp Lid

model). To take the lid off (fig. 7), hold it on both sides

and open it. Pull the lid upwards, then close it slowly

to unhook it.

- To reposition the lid (Base Camp Lid model) (fig. 8),

insert the tabs located at the rear of the lid into the

slots at the rear of the device. Open the lid comple-

tely, then close it without forcing.

- Store the device in a dry, ventilated place.

- If the device has not been used for 30 days, check to

see that cobwebs are not clogging the burner hose

openings; this could lead to decreased burner effi-

ciency or to a dangerous ignition of gas outside the

burner.

2) Flexible hose or hose between the regulator and

the stove

- Regularly check the condition of the hose/hose and

change it if it shows signs of ageing or cracking.

- France, if the expiry date printed on the hose or hose

has been reached, the flexible hose and collars must

be replaced by components meeting the require-

ments of standard XP D 36-110.

- Follow the assembly instructions supplied with these

new models, the length of which must not exceed

1.50 m, and proceed as described in Section A - 2).

- If your stove is likely to be left unused for a long

period, disconnect the gas cylinder.

Important:

An overall inspection and leaks check must be carried

out at least annually and always after changing the gas

cylinder.

C - OPERATION

SAFETY PRECAUTIONS :

Do not use your stove at a distance closer than 20

cm to a wall or flammable object, nor closer than

1 metre to a ceiling.

WARNING: Accessible parts may be very hot.

Keep young children away.

Never touch the pan support (2) or the burner

during or just after using the equipment.

Never use the equipment without the pan support

(see fig. 2).

Position the equipment on a stable, horizontal

surface and do not move when in use.

Do not use a container smaller than 12 cm or lar-

ger than 20 cm in diameter.

In the event of a leak (smell of gas), close all val-

ves.

Wait for the stove to cool down completely before

handling it to return it to its place of storage.

After use, always close the valve on the regulator

or gas cylinder.

Do not move the device when it is in operation.

During operation, the temperature of the support

base may be elevated. The device should not be

placed on a combustible surface (plastic, table-

cloth, etc.). Place an adequate, non-combustible,

thermal insulating material between the device

and its support base.

1) Lighting up (fig. 3)

- Open the gas supply (valve or lever on regulator).

- Present a flame close to the burner and turn the bur-

ner control knob (1) anti-clockwise.

- Adjust the flame to receptacle dimensions by turning

the wheel. Do not use receptacles with a diameter

larger than 20 cm.

- If you would like to fine-tune the simmering tempera-

ture, adjust the flame level by turning the wheel.

- In case of strong wind, place the device with the lid

facing the wind (Base Camp Lid model) so that the

wind does not make the burner flame flare up beyond

the pan bottom.

- When cooking is finished, turn the wheel (1) corres-

ponding to the burner in a clockwise direction to the

(l) position (fig. 6).

2) SHUTTING DOWN

- Close the valve on the regulator or gas cylinder.

- When the flames have gone out, close the stove val-

ves (1) by turning the control knobs to position (l)

(fig. 6).

D - REMOVING OR CHANGING THE GAS

CYLINDER

- Check that the gas cylinder valve or regulator lever is

in the closed position.

- Disconnect the regulator from the gas cylinder.

- Install the new gas cylinder.

- Connect the regulator to the new gas cylinder (check

the condition of the regulator seal, before connecting

it to the gas cylinder).

IFU SG_208_22 - Base Camp - octobre 2011.qxp 10/10/2011 11:48 Page 10

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Campingaz Base Camp Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info