Bedienungsanleitung Campingaz Expert Plus2014 (Seite 7 von 88) (Alle Sprachen)

662287

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

Important:

If the burner fails to light after the 2

attempt, turn the

control knob to the "off" position (l) and check that the

burner oulets and venturi tubes are not blocked.

If your apparatus has only 1 control knob

Read steps 1 to 5 before beginning with step 1.

1) Make sure the control knob is in the "off" (l) position.

2) Push the end of the hose completely onto the regulator

nozzle and secure with a suitable clip.Fit the regulator onto

the gas cylinder in accordance with its instructions.

3) Open the gas cylinder valve.

4) Press the control knob and turn it to the full flame ( )

position, then immediately press the igniter button ( )

until you hear the click. Repeat 3 or 4 times if necessary

until the burner is lit.

5) If the burner fails to light,turn the control knob to the "off"

position (l). Wait 5 minutes before repeating the

operation.

Important:

If the burner fails to light after the 2

attempt, turn the

control knob to the "off" position (l) and check that the

burner outlets and the venturi tube are not blocked.

i) Grill burner-manual lighting

If the automatic ignition should fail to operate, turn the control

knob to the "off" position (l) and wait 5 minutes. Insert a

burning match into one of the side openings of the base, and

turn the knob on the right of the control panel onto the full

flame ( ) position.

j) Turning off the grill burner

Return the control knobs to the "off" position (l), then close

the cylinder valve.

k) Lighting the side stove (if applicable to your model)

The stove may operate independently or in conjunction with

the grill burner.

Lighting:

- open the gas cylinder valve.

- check that there is no gas leak between the gas cylinder and

the stove.

- check the condition of the hose connecting the grill burner to

the stove.Should it present cracks,call our After Sales Service

to have it replaced.

- open the valve of the stove (towards the +) and press the

igniter button ( ) until you hear the click. Repeat three or

four times if necessary. Should the stove fail to light, present

a match to the edge of the burner.

- adjust the size of the flame to the dimensions of the container

you are using by opening the valve to various extents. Do not

use a container smaller than 10 cm or larger than 26 cm.

l) Turning off the side stove (if applicable to your model)

Close the stove valve (towards the -) and the valve of the gas

cylinder if the grill burner is not in use.

m) Replacing the gas cylinder

- Always work in a well ventilated area and never in the

presence of a flame, spark or heat source.

- Return the control knobs in the "off" position (l) then close

the cylinder valve.

- Remove the regulator, check that the sealing joint is in good

condition.

- Put the full cylinder in place, refit the regulator,taking care not

to apply stress to the hose. Check for gas leaks.

n) Operation

If your apparatus has a lid

- It's recommended that protective gloves be worn to handle

components which may be very hot.

- Before cooking, preheat the barbecue for about 10 minutes

in the full flame ( ) position with the lid closed.

4) Fit the regulator onto the gas cylinder in accordance with

its instructions.

5) Use a gas leak solution to test for leaks. Important: never

use a naked flame to check for gas leaks.

6) Apply the solution to the connections cylinder/regulator/

hose/apparatus (the control knobs should remain closed: off

position). Open the gas cylinder valve.

7) Bubbles in the gas leak solution indicate that there are gas

leaks.

8) The leak can be stopped by tightening any hose connection

or replacing any faulty component. The barbecue must not

be used until the leak is stopped.

9) Close the valve on the gas cylinder. Check for leaks at least

once per year and each time the gas cylinder is replaced.

g) Prior to use

Never use the barbecue until the instructions have been read

carefully and understood. Also, make certain that:

- there are no leaks

- the venturi tubes are not blocked

- the hose does not touch any components which may get hot.

- that the ventilation openings in the gas receptacle housing are

not obstructed, if appropriate.

Check that the venturi tubes (VT) cover

the injectors (IJ).

h) Lighting the grill burner

If your apparatus has 2 control knobs

Read steps 1 to 7 before beginning with step 1.

1) Never light the barbecue with the lid closed, only

with the lid open.

2) Make sure the 2 control knobs are in the "off" (l) position.

3) Push the end of the hose completely onto the regulator

nozzle and secure with a suitable clip.Fit the regulator onto

the gas cylinder in accordance with its instructions.

4) Open the gas cylinder valve.

5) Press one of the 2 control knobs and turn it to the full

flame ( ) position, then immediately press the igniter

button ( ) until you hear the click.Repeat 3 or 4 times if

necessary until the burner is lit.

6) If the burner fails to light,turn the control knob to the "off"

position (l). Wait 5 minutes before repeating the

operation.

7) As soon as the burner is lit, the other burner automatically

lights when the second control knob is placed in the full

flame ( ) position without pushing the automatic igniter

button again.

76622-04.qxp 12/03/2013 13:49 Page 7

Campingaz Expert Plus2014 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info