Bedienungsanleitung Camry CR 7739 (Seite 8 von 124) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch)

802399

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

DO NOT COVER« INSCRIPTION IMPORTANCE

The inscription on the device means that the device is not to be covered with clothing, blankets

and other textile products which could cause ignition.

"Caution Hot Surface" - The temperature of available surfaces may be

higher when the equipment is working, which means that the housing

elements become very hot during operation during operation, SAVE

CAREFUL !!!

To protect your environment: please separate carton boxes and plastic bags and dispose them in corresponding waste bins.

Used appliance should be delivered to the dedicated collecting points due to hazarsous components, which may effect the

environment. Do not dispose this appliance in the common waste bin.

WARNING: Do not use this equipment near bathtubs, showers, swimming

pools and similar water tanks.

E. Temperature unit button F. Temperature increase button

G. Temperature decrease button H. Frost protection indicator

I. TURBO FAN indicator J. Selected temperature indicator

K. Room temperature indicator L. Time remaining indicator to turn off the device

M. Selected heating level indicator

The remote control (7) operation way is same as buttons on control panel (6).

USAGE

1.Turn on the device by pressing by hand the power switch (1) on the left side of device.

2. Press the power button (A) to illuminate the control panel (6), the device is ready to operate now.

3. To set the heat output press the heat output button (B) the appropriate number of times, the required heat level setting is achieved:

- one time pressing means low heat setting - 750W heat output, it will be shown on control panel,

- two times pressing means middle heat setting - 1250W heat output, value will be shown on control panel,

- three times pressing means high heat setting - 2000W heat output, value will be shown on control panel,

- four times pressing means the device come into frost protection function, snowflake indicator (H) will be shown on control panel.

The frost-proof mode is turned on, 5° C / 41 ° F are a fixed temperature value, when the environment temperature is below 5° C /

41 ° F , the device will start heat mode automatically at 2000W heating level until room temperature reaches 9° C / 48 ° F. Later the

heating is turned off to standby, followed by cycling.

4. To switch the TURBO fan on, press the button (C), the fan indicator (I) will be illuminated. Fan starts to operate. To stops the fan

press the button (C) again.

5. To setting the period of time the device will switch off you can use timer function. To preset a switch off time press the timer button

(D) appropriate number of times to choose operation time between 1-24 hours. The device will switch off automatically after chosen

period of time.

6. To setting the temperature units (F/C) that means: F = Fahrenheit and C = Centigrade press the temperature units button (E) the

appropriate number of times until the required temperature units setting is achieved.

7. To increasing the temperature setting press the button (F) the appropriate number of times until the required increased

temperature setting is achieved. The selected temperature setting (J) is indicated on the control panel. The range of temperature is

5-37°C / 41-99°F.

8. To decrease the temperature setting press the button (G) the appropriate number of times until the required decreased

temperature setting is achieved. The selected temperature setting (J) is indicated on the control panel.

Note: the control panel (6) always shows the last set temperature (J) and present the room temperature (K). If the heat function

switches itself off then set temperature (J) had been achieved in the immediate area of the device.

When the room temperature (K) reaches the set temperature level (J), the heating element stops to work. When room temperature

(K) is 1 degrees over the set temperature level (J), the heating element also will stop to work. The heating element will begin

operating again only when the room temperature decreases 1 degrees with respect to the set temperature.

9. To switch off the device press power button (A) and next switch off the power switch (1).

After around 1 minute of last action the control panel (6) stops to illuminate but the device is operating according to last setting.

CLEANING AND MAINTENANCE

1. Always unplug the appliance from the power socket before cleaning.

2. If during cleaning items such as the power plug, thermostat, electrical contacts etc. are soaked before being used again, they

should be thoroughly dried.

3. Do not use aggressive detergents in the form of emulsions, lotions, pastes, etc. to clean the cabinet. They can, among other

things, remove the information graphic symbols, such as signs, warning signs, etc.

4. Ensure that the device has cooled down before cleaning.

5. When the device is not used for long periods of time, it should be protected against dust and stored in a clean dry place.

TECHNICAL DATA:

Voltage: 220-240V ~50/60Hz

Power: 1800-2000W

Max. Power: 2000W

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Camry CR 7739 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info