Bedienungsanleitung Cannondale Topstone Neo Carbon 2020 (Seite 16 von 20) (Englisch)

804892

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

Topstone Neo Carbon OMS

Technical Information

Seat Post

Technical Information

Seat Post

138222 Rev 1 (03/20)

Seat Binder Inspection

The internal seat binder system consists of a sliding clamp assembly and a nut base with a

double-side adhesive holding it to a special mating surface inside the seat tube. The sliding

clamp parts can be removed when the seat post is out.

Always clean the surfaces of the sliding clamp by wiping them with a clean dry lint-free shop

towel only. Do not soak the parts, as the internal washer is lubricated with grease. Solvents

will wash out the lubricant and the assembly will have to be regreased by disassembling it

completely.

NOTICE

If the nut base has become rotated, it should be removed and re-axed to the frame. The process is

described in the Service Instruction for the parts kit. These instructions are not provided in this manual.

We reccommend that you have a Cannondale Dealer perform the replacement.

Please Note: During ﬁrst assembly of the nut base, it is important to not push on the 4mm allen

when tightening onto the seatpost. This can disengage the adhesive tape before proper bonding.

A poor bond can lead to misalignment. The 3M™ VHB™ Tape 5980 is pressure sensitive.

To inspect

1. To remove the seat post. See previous

page.

2. To remove the sliding clamp, use a 4

mm hex key and turn grub screw slowly

clockwise until the clamp is disengaged

from the nut base.

3. Use the 4 mm hex to push the clamp out

through the seat tube opening.

4. Look into the frame opening. Use a pen

ﬂashlight. Check the position of the nut

base. See CORRECT next page.

5. If the nut base is missing, or rotated or

damaged, a replacement is required.

This service should be performed by a

Cannondale Dealer.

6. Check the condition of the clamp. The

seat post face and frame contact surfa-

ces should be smooth. If they are not, the

clamp assembly should be replaced with

a new one.

7. Clean the parts and inside the seat tube

with a dry shop towel and re-apply grease

and carbon paste as indicated.

8. Returning the sliding clamp to the frame,

using the 4 mm hex to guide it to the nut

base.

9 Turn the grub screw counter-clockwise

to engage the nut base. Make sure it is

enaged suciently to easily insert the

seat post into the seat tube.

CRB-GEL

NGLI-2

Identiﬁcation

1. Sliding Clamp

2. Roll Pins (2X)

3. Washer

4. Grub Screw

5. Nut Base

6. Pressure Sensitive Adhesive Tape

(Double-sided)

This is INCORRECT.

The nut plate is rotated.

This is CORRECT.

Correct application

of carbon paste

and grease.

(shown disassembled)

The pressure sensitive adhesive

double-sided tape secures the

aligned nut base in the frame.

When applied the nut base and

frame should be very clean for a

good bond.

Ready to accept seat post.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cannondale Topstone Neo Carbon 2020 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cannondale Topstone Neo Carbon 2020

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info