Bedienungsanleitung Canon VB-S30D (Seite 40 von 185) (Englisch)

630614

Zoom out

Zoom in

Vorherige Seite

1/185

Nächste Seite

Administrator Password

(1) [Password]

Set the administrator password. Up to eight (single-

byte) ASCII characters (space or printable

characters) can be used. The factory default setting is

“camera”. If the Admin Viewer, Admin Tools, etc., are

connected, terminate the connection before changing

the password.

(2) [Confirm Password]

Enter the same password as above for confirmation.

LAN

(1) [LAN Interface]

Select [Auto], [Full Duplex] or [Half Duplex]. Normally

[Auto] is used.

(2) [Maximum Packet Size]

Enter the maximum transmission unit. Normally there

is no need to change the default setting of 1500.

Note

When using ADSL, setting the maximum packet size to a slightly

lower value may increase sending efficiency.

IPv4

(1) [IPv4 Address Setting Method]

Select [Manual] or [Auto (DHCP)] in the address

setting method. If [Manual] is selected, directly enter

the values according to the environment in which the

camera is used. If [Auto (DHCP)] is selected, the value

automatically acquired from the DHCP server will be

entered in [IPv4 Address], [Subnet Mask] and [IPv4

Default Gateway Address].

(2) [IPv4 Address]

If [Manual] is specified in (1), enter a fixed IP address.

(3) [Subnet Mask]

If [Manual] is specified in (1), enter the designated

subnet mask values for each network.

[Network]

Setting Administrator Password, LAN, IP Address, DNS, etc

The following can be set here.

• Administrator Password

Set the administrator password.

•LAN

Set the IP address and other items needed to

establish a LAN connection.

•IPv4

Set IPv4 address.

•IPv6

Set IPv6 address.

•DNS

Set the name server address, host name and

DDNS registration.

•mDNS

This will configure settings for using multicast

DNS.

• SNMP

Configure the necessary settings to use SNMP.

Important

• To ensure system security, be sure to change the

administrator password. If it is not changed, a message

prompting change of the password will appear continuously

in the upper portion of the Setting Menu. The message will

not disappear until the password is changed. Do not forget

the new password.

• Press the reset switch to restore factory default settings if you

have forgotten the administrator password (p. 167). Note,

however, that this will reset all camera settings to factory

default settings except for date and time.

• [Administrator Password] and [Access Control] >

[Administrator Password] (p. 64) are the same. If you set one

[Administrator Password], the setting will be reflected in the

other [Administrator Password].

Important

• The camera may become inaccessible from the active web

browser if [LAN Interface] or [Maximum Packet Size] settings

are changed. Check beforehand the precautions in

“Important” in “[Reboot Item] Setting Items Requiring

Rebooting” (p. 76).

• Set [Maximum Packet Size] to 1280 or greater if using IPv6.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Canon VB-S30D Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Canon VB-S30D

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info