Bedienungsanleitung Canon XHG1 (Seite 145 von 155) (Englisch, Französisch, Spanisch)

543015

145

Zoom out

Zoom in

Vorherige Seite

1/155

Nächste Seite

145

Additional Information

Troubleshooting

If you have a problem with your camcorder, refer to this checklist. Consult your dealer or a Canon

Service Center if the problem persists.

Power Source

Recording/Playback

Recording

Problem Cause Solution

Camcorder will not turn on. Battery pack is not correctly attached. Attach the battery pack correctly. 16

The camcorder switches off by itself. Power save function has been activated. Turn on the camcorder. 31

The screen switches on and off. Battery pack is exhausted. Replace or charge the battery pack. 16

Problem Cause Solution

Buttons will not work. Cassette is not loaded. Load a cassette. 25

flashes on the screen. Condensation is detected. See reference page. 144

“REMOVE THE CASSETTE” appears on the

screen.

Camcorder stopped operating to protect the

tape.

Remove the cassette and reinsert it. 25

The wireless controller will not work. Camcorder and wireless controller are not

set to the same remote sensor mode.

Change the remote sensor mode. 111

Batteries of the wireless controller are

exhausted.

Replace the batteries. 24

Abnormal characters appear on the

screen. The camcorder does not operate

properly.

This camcorder uses a microcomputer.

External noise or static electricity may cause

abnormal characters to appear on the

screen.

Disconnect the power source and

reconnect it after a short time. If the

problem still persists, disconnect the power

source and reset all the camcorder’s

settings to default values using the

[SYSTEM SETUP/ ] [RESET ALL]

setting.

–

Problem Cause Solution

The dial is not in the OFF

position but the POWER indicator is off.

The LED indicators option in the customized

functions is set to [OFF].

Set the [LED] setting to one of the other

types.

102

Image will not appear on the screen. The dial is not set to a recording

program.

Set the dial to a recording

program.

“SET THE TIME ZONE, DATE AND TIME”

appears on the screen.

Time zone, date and time are not set, or the

built-in rechargeable lithium battery is

exhausted.

Set the time zone, date and time. If

necessary, power the camcorder with the

compact power adapter and leave it

connected with the dial set to

OFF for at least 24 hours to recharge the

built-in battery before making the settings.

Pressing the START/STOP button will not

start recording.

Cassette is not loaded. Load a cassette. 25

The dial is not set to a recording

program.

Set the dial to a recording

program.

The LOCK switch is set to prevent the

operation of the controls on the carrying

handle.

Slide the LOCK switch to the left to enable

the operation of the carrying handle

controls.

Camcorder will not focus. Autofocus does not work on that subject. Focus manually. 38

Viewfinder is not adjusted. Adjust the viewfinder with the dioptric

adjustment lever.

Lens is dirty. Clean the lens. 140

The tally lamp will not light up. The tally lamp option in the customized

functions is set to [OFF].

Set the [TALLY LAMP] setting to [ON] or

[BLINK].

102

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Canon XHG1 Seite 145

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Canon XHG1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info