Bedienungsanleitung Canon XHG1 (Seite 146 von 155) (Englisch, Französisch, Spanisch)

543015

146

Zoom out

Zoom in

Vorherige Seite

1/155

Nächste Seite

146

Recording

Playback

Memory Card Operations

About the LCD screen

The LCD screen is produced with extremely high-precision manufacturing techniques, with more than

99.99% of the pixels operating to specification. Less than 0.01% of the pixels may occasionally misfire or

appear as black, red, green or blue dots. This has no effect on the recorded image and does not constitute a

malfunction.

Problem Cause Solution

A vertical light bar appears on the screen. Bright light in a dark scene may cause a

vertical light bar (smear) to appear. This is

not a malfunction.

Record in Av mode with an aperture value

in the range F5.6–F8.0.

Viewfinder picture is blurred. Viewfinder is not adjusted. Adjust the viewfinder with the dioptric

adjustment lever.

Audio is not recorded. The input channel is not set correctly. Set the appropriate input channel. 51

Microphone connected to the XLR terminal

needs to be powered by the phantom power.

Set the switch to ON. 51

Audio is recorded in a very low level. The switch is set to M, and

recording level is set too low.

Adjust the audio level correctly. 51

Microphone attenuator is turned on. Set the FRONT MIC ATT. switch or the

switch to OFF.

Problem Cause Solution

Pressing the playback button does not

start playback.

Camcorder is turned off, or is not set to

mode.

Set the camcorder to mode. 107

Cassette is not loaded. Load a cassette. 25

Tape is running, but image will not appear

on the TV screen.

Video heads are dirty. Clean the video heads. 143

You attempted to play back or dub a

Stop playback/dubbing. –

The video output cable is not connected

correctly.

Verify that the video cable is connected

properly.

–

While playing back a tape recorded in HDV

standard there are brief stops in the

playback picture.

Video heads are dirty. Clean the video heads with a dry cleaning

cassette.

143

Problem Cause Solution

Memory card cannot be inserted. Memory card was not facing the correct

direction.

Turn the memory card over and try

inserting it again.

Memory card cannot be recorded. No memory card. Insert a memory card. 26

Memory card is full. Replace the memory card or erase images. 122

Memory card is not initialized. Initialize the memory card. 124

The folder and file numbers have reached

their maximum value.

Set [FILE NOS.] to [RESET] and insert a new

memory card.

113

Memory card cannot be played back. The dial or / (card/tape)

switch are not set to the correct position.

Set the dial to VCR/PLAY and the

/ (card/tape) switch to .

120

Image cannot be erased. Image is protected. Cancel the protection. 123

On an SDHC or SD memory card, the write-

protect switch is set to the locked position.

Change the position of the write-protect

switch on the memory card to unlock it.

142

flashes red. Card error occurred.

Turn off the camcorder. Remove and

reinsert the memory card. Initialize the

memory card if flashing persists.

124

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Canon XHG1 Seite 146

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Canon XHG1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info