Bedienungsanleitung Carat CARACOUP 100 ALU (Seite 12 von 47) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch)

816453

Zoom out

Zoom in

Vorherige Seite

1/47

Nächste Seite

ENGLISH

There are the following symbols and information signs on

the machine that refer to potential dangers:

Warning of rotating tool!

Running direction of the

saw blade

Wear gloves. Wear ear

protectors. The machine

meets EU guideline.

Observe the operating

manual. Wear protective

goggles

Laser

Class 2

635 mm

DO NO T

STARE

INTO

BEAM

ATTENTION

Rotation direction

3. MACHINE DATA

3.1 Diamond blades

DANGER!

Risk of injury by defective or incorrectly mounted

diamond blades!

Wrong rotation direction and damaged diamond blades

may cause injuries of personnel! Check diamond blades

for broken o segments and segment pieces, segment

foot cracks, diamond blade deformations or signs of

wear before starting work. Pay attention to the rotation

direction arrows on the diamond blades and guard!

DANGER!

Risk of injury by unchecked or unapproved tool!

Diamond blades or buzz saw blades that have not been

checked or approved may cause injuries of personnel!

Before starting work, check whether a proper diamond

blade is mounted. Pay attention to the rotation direction

arrows on the diamond blade and guard!

NOTE!

All diamond blades used must be designed in

terms of their permissible max. cutting speed to match

the max. drive speed and intended application of the

machine tool

Diamond blade Diameter Material

Carat tile and

natural stone

diamond blade

Ø 200

Tile, ceramic,

stoneware, natural

and articial stone,

thin granite

3.2 Type plate

The type plate is located on the base frame of the machine

tool.

3.3 Installation site requirements

The oor surface must:

- Have suicient load bearing capacity.

- Be slip proof.

- Be level.

3.4 Storage requirements

Storage conditions

As a matter of principle, the machine, its components,

assemblies or parts must be only stored in the following

conditions:

do not store outdoors. store in dry and dust-free place.

do not expose to aggressive media. protect from

solar radiation. avoid mechanical vibrations. storage

temperature range 5 to 45°C

relative air humidity, max. 60%. In case of storage for

over 3 months, check general condition of all parts and

packaging on a regular basis. If necessary, renew or replace

conservation materials.

4. TRANSPORT

ATTENTION!

Damage through improper transportation!

Improper transportation can result in considerable

damage of the machine and objects in the vicinity.

Before every transport:

- The cutter head must be locked.

- The cutter head must be lowered and locked.

- The cutting table must be secured by the table lock

(for table saw machines).

- The machine must be disconnected from power supply.

Due to two transport rollers, the machine can be

transported by one or two persons who can use transport

handles.

Instruction of using crane liing eyes

The machine is designed for crane transport by means of

the liing eye.

Always check the tighteness of the liing eyes before using

it to transport the machine. To avoid damage, also check

that the liing straps do not touch the motor when liing.

CAUTION!

Risk of injury due to improper handle when it is

transported by crane.

CAUTION!

Risk of injury by standing under the machine when

it is transported by crane.

CAUTION!

Risk of injury of falling material from the working

table, it is not allowed to have any material on working

table when it is transported.

Crane liing eyes P-3510 / P-3512 / CARACOUP 104 ALU /

CARACOUP 100 ALU

5. INSTALLATION

5.1 Connection

Before connecting the machine to the power source,

make sure that:

- Voltage / phase of the power supply, match the date on

the type plate of the motor and machine.

- The power supply line is grounded according to the safety

provisions.

- The wire size of the extension cord is suicient, H07RNF

3x2.5 mm² up to 50m for 230V.

5.2 Mounting a diamond blade

To mount a new diamond blade or replace the used one,

proceed as follows:

1. Switch o the machine and interrupt the power supply

by pulling the mains cable from the mains outlet.

2. Loosen the screws on the diamond blade guard so as to

be able to remove the front half of the diamond blade

guard.

3. Loosen the nut of the motor sha and remove the outer

cutter ange.

4. Clean the cutter ange, nut and motor sha.

5. Check the parts for signs of wear.

6. Mount or replace the diamond blade. While doing so,

pay attention to the correct rotation direction of the

diamond blade and motor sha.

7. Replace the outer cutting ange on the motor sha.

8. Screw the nut onto the motor sha again and tighten it

rmly.

9. Replace the front half of the cutting wheel guard to

connect it with the rear half.

10. Tighten rmly the screws on the cutting wheel guard.

NOTE!

The arrow on the cutting wheel indicates

correct rotation direction.

NOTE!

The cutting wheel, irrespective of its position or

the position of the cutter head, may not touch the table!

5.3 Mounting the transport handles and wheels

Mount the transport handles at the appropriate places on

the base frame using the supplied washers (4x A8,4 ISO

7089) and the screws (4x M8x30 ISO 4017), the spring wash-

ers (4x A8 DIN 127) and the screws (4x M8x20 ISO 4017).

Do the same with the transport wheels. Mount the trans-

port wheels at the appropriate places on the base frame

using the supplied washers (4x A,8,4 ISO 7090), the spring

washers (4x A8 DIN127), the screws (4x M8x25 ISO 4017)

and the nuts (4x M8 ISO 4032).

Mounting the extension table

If you want to work with the extension table, proceed as

follows:

Carat CARACOUP 100 ALU Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info