Bedienungsanleitung Carat P-SERIE (Seite 12 von 47) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch)

816455

Zoom out

Zoom in

Vorherige Seite

1/47

Nächste Seite

2322

ENGLISH

4. TRANSPORT

ATTENTION!

Damage through improper transportation!

Improper transportation can result in considerable damage

of the machine and objects in the vicinity.

Before every transport:

- The cutter head must be locked.

- The cutter head must be lowered and locked.

- The cutting table must be secured by the table lock

(for table saw machines).

- The machine must be disconnected from power supply.

Due to two transport rollers, the machine can be

transported by one or two persons who can use transport

handles.

Instruction of using crane liing eyes

The machine is designed for crane transport by means of

theliingeye.

Alwayscheckthetightenessoftheliingeyesbeforeusing

it to transport the machine. To avoid damage, also check

thattheliingstrapsdonottouchthemotorwhenliing.

CAUTION:

Risk of injury due to improper handle when it is

transported by crane.

CAUTION:

Risk of injury by standing under the machine when

it is transported by crane.

CAUTION:

Risk of injury of falling material from the working

table, it is not allowed to have any material on working

table when it is transported.

Crane liing eyes P-3515 / P-3520

P-3510 / P-3512 / CARACOUP 104 ALU / CARACOUP 100 ALU

5. INSTALLATION

5.1 Connection

Before connecting the machine to the power source,

make sure that:

- Voltage / phase of the power supply, match the date on

the type plate of the motor and machine.

- The power supply line is grounded according to the safety

provisions.

-Thewiresizeoftheextensioncordissuicient,H07RNF

3x2.5 mm² up to 50m for 230V.

5.2 Mounting a diamond blade

To mount a new diamond blade or replace the used one,

proceed as follows:

1.Switchothemachineandinterruptthepowersupply

by pulling the mains cable from the mains outlet.

2. Loosen the screws on the diamond blade guard so as to

be able to remove the front half of the diamond blade

guard.

3.Loosenthenutofthemotorshaandremovetheouter

cutterange.

4.Cleanthecutterange,nutandmotorsha.

5. Check the parts for signs of wear.

6. Mount or replace the diamond blade. While doing so,

pay attention to the correct rotation direction of the

diamondbladeandmotorsha.

7.Replacetheoutercuttingangeonthemotorsha.

8.Screwthenutontothemotorshaagainandtightenit

rmly.

9. Replace the front half of the cutting wheel guard to

connect it with the rear half.

10.Tightenrmlythescrewsonthecuttingwheelguard.

NOTE!

The arrow on the cutting wheel indicates

correct rotation direction.

NOTE!

The cutting wheel, irrespective of its position or

the position of the cutter head, may not touch the table!

5.3 Mounting the transport handles and wheels

Mount the transport handles at the appropriate places on

the base frame using the supplied washers (4x A8,4 ISO

7089) and the screws (4x M8x30 ISO 4017), the spring wash-

ers (4x A8 DIN 127) and the screws (4x M8x20 ISO 4017).

Do the same with the transport wheels. Mount the trans-

port wheels at the appropriate places on the base frame

using the supplied washers (4x A,8,4 ISO 7090), the spring

washers (4x A8 DIN127), the screws (4x M8x25 ISO 4017)

and the nuts (4x M8 ISO 4032).

Mounting the extension table

If you want to work with the extension table, proceed as

follows:

Insert the extension table into the lateral grommets on the

base frame and tighten it with the star grip screws

5.4 Fill the water tank

Thewatertankmustbelledbeforethemachineis

started. Use clear, clean water for this.

ATTENTION!

The water pump may not run without water,

otherwise it can be damaged.

6. OPERATION

6.1 Intended working position of the operator

The operator takes position in front of the machine near

the switch and the chain driven handwheel to be able to

slide the cutter head with the handwheel and to press the

red stop button at any time.

6.2 Start-up preparation

To safely use the machine as intended, the following

preconditions must be met:

-Themachinestandsrmly.

-Thewatertankislledwithclean,clearwater.

- The machine has been checked for damage, loose screw

connections and integrity.

- The water supply is functional.

- Rotation direction arrows on the cutting wheel and guard

match.

- An appropriate cutting wheel must be installed, which

meets optimum conditions.

6.3 Start-up

The machine is switched on by the main switch. For this

purpose, press the green button to start

Aer the start, check the following:

The cooling water must be pumped to the cutting wheel

bythewaterpumpinthesuicientquantitiesanddraino

on both sides. If this is not the case, stop the machine im-

mediately! The motor is equipped with thermal insulation

activated when the temperature rises too high.

Wait approx. 30 minutes before restarting the machine

until the motor cools down

Carat P-SERIE Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info