Bedienungsanleitung Carat P-SERIE (Seite 13 von 47) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Schwedisch)

816455

Zoom out

Zoom in

Vorherige Seite

1/47

Nächste Seite

2524

ENGLISH

6.4 Cutting operation

6.4.1 Normal cutting in 90° position

When cutting in 90° position, the cutter head remains at a

xedpoint.Foradjustment,proceedasfollows:

1.Switchothemachine->thecuttingwheelmuststop

rotating!

2. Loosen the adjusting screw.

3. Set the cutter head in the desired position.

4. Tighten the adjusting screw -> check if the cutter head is

adjusted in height and make sure that it cannot move.

5. Put the material to be cut onto the table (for table saw

machine position it directly at the material stop).

6. Check the position of the material using the angle stop.

7. Start the motor and the water pump and open the water

tap.

8. Grab the cutter head’s chain driven hand crank with the

right hand and the transport handle on the frame with

thelehand.

9. Then slowly slide the cutter head through the material

to be cut, without pressure. The cutting wheel then cuts

through the material on the table.

NOTE!

The cutting wheel, irrespective of its position or

the position of the cutter head, may not touch the table!

NOTE!

In emergency, press the red stop button on the

switch by the le hand.

Cutting method: 45° bevel cuts

Themachineoersthepossibilityofperforming45°bevel

cuts. To perform 45° bevel cuts, proceed as follows:

1.Switchothemachine->thecuttingwheelmuststop

rotating!

2. Loosen the star grip screws on the bridge on both sides

of the machine.

3. Pivot the complete cutter head including the bridge into

the desired position. Orientate yourselves on the lateral

scale.

4. Tighten again the star grip screws.

5. Then loosen the adjusting screw.

6.Adjustthedepthstopandxthissetting.

7. Put the material to be cut on the table. Check the

material’s position using the angle stop.

8. Start the motor and the water pump and open

the water tap.

9. Grab the cutter head’s chain driven hand crank with

the right hand and the transport handle on the frame

withthelehand.

NOTE!

In emergency, press the red stop button on the

switch by the le hand.

NOTE!

The cutting wheel, irrespective of its position or

the position of the cutter head, may touch neither the

table, nor the back square!

To bring back the guiding bridge and the cutter head to the

90°positionaerthecuttingoperation,proceedasfollows:

1.Switchothemachine->thecuttingwheelmust

stop rotating!

2. Loosen the star grip screws on the bridge on both

sides of the machine.

3. Pivot the complete cutter head including the bridge

into the desired position. Orientate yourselves on the

lateral scale.

4. Firmly tighten again the star grip screws.

NOTE!

Hold rmly the cutter head with the hand

in the 90°¬ position. Tightening the nut can turn the

square back so that the angle of the cutter head is

not exactly 90°.

NOTE!

The cutting wheel, irrespective of its position

or the position of the cutter head, may not touch the

cutting table!

6.4.2 Water supply

Heavily polluted water decreases the service life of the

water pump and cutting wheel.

For frequent use, change water several times a day, and

collect,lteranddisposeofthecuttingmud

Clean the suction strainer of the water pump every time

the water is changed

6.5 Stop cutting operation

Use the red stop switch on the motor to stop the machine.

7. MAINTENANCE & CLEANING

Before performing any maintenance, make sure the

machine is disconnected from electrical power.

For long-term quality, please perform the following

maintenanceactionsaerusingthemachine

- Visually inspect the entire machine.

-Cleantheangeandblademounting.

- Clean engine (housing + cooling fans), water tank, water

pump,waterpumplter,waterhosesandnozzles,table

guide rails, table wheels.

- Make sure all bolts and screws are tightened.

Before using the machine, make sure that all the above

actions have been performed.

een korte rustpauze.

8. DISPOSAL

If no return or disposal agreement was made, send the

dismantled components for recycling:

- Scrap metal parts.

- Hand over plastic parts for recycling.

- Dispose of other components assorted according to

material characteristics.

EU countries only

Electric waste is recyclable and must not be

disposed of in the household waste!!

According to the European directive 2012/19/EU on

electrical and electronic waste and version transposed

into national law, used power tools must be collected

separately and sent for recycling in an environmental-

friendly manner.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Carat P-SERIE Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info