Bedienungsanleitung Carat SL-1255 DUSTEC (Seite 33 von 98) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Schwedisch, Norwegisch)

816481

Zoom out

Zoom in

Vorherige Seite

1/98

Nächste Seite

. Maintain a firm grip on the power tool and position your body and arm to allow you to resist

kickback forces. Always use auxiliary handle, if provided, for maximum control over kickback or

torque reaction during start-up. The operator can control torque reactions or kickback forces, if proper

precautions are taken.

. Never place your hand near the rotating accessory. Accessory may kickback over your hand.

. Do not position your body in line with the rotating wheel. Kickback will propel the tool in direction

opposite to the wheel’s movement at the point of snagging.

. Use special care when working corners, sharp edges etc. Avoid bouncing and snagging the

accessory. Corners, sharp edges or bouncing have a tendency to snag the rotating accessory and cause

loss of control or kickback.

. Do not attach a saw chain, woodcarving blade, segmented diamond wheel with a peripheral gap

greater than 10 mm or toothed saw blade. Such blades create frequent kickback and loss of control.

. Do not “jam” the wheel or apply excessive pressure. Do not attempt to make an excessive depth of

cut. Overstressing the wheel increases the loading and susceptibility to twisting or binding of the wheel

in the cut and the possibility of kickback or wheel breakage.

. When wheel is binding or when interrupting a cut for any reason, switch off the power tool and

hold the power tool motionless until the wheel comes to a complete stop. Never attempt to remove

the wheel from the cut while the wheel is in motion otherwise kickback may occur. Investigate and

take corrective action to eliminate the cause of wheel binding.

. Do not restart the cutting operation in the workpiece. Let the wheel reach full speed and carefully

re-enter the cut. The wheel may bind, walk up or kickback if the power tool is restarted in the workpiece.

. Support panels or any oversized workpiece to minimize the risk of wheel pinching and kickback.

Large workpieces tend to sag under their own weight. Supports must be placed under the workpiece

near the line of cut and near the edge of the workpiece on both sides of the wheel.

. Use extra caution when making a “pocket cut” into existing walls or other blind areas. The

protruding wheel may cut gas or water pipes, electrical wiring or objects that can cause kickback.

5) SERVICE

Have your power tool serviced by a qualified repair person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

Symbols used in this manual

V……........volts

A……........amperes

Hz……......hertz

W…….......watt

~………....alternating current

………..no load speed

min-1…......revolutions or reciprocation per minute

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Carat SL-1255 DUSTEC Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info