Bedienungsanleitung Carat SL-1255 DUSTEC (Seite 34 von 98) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Schwedisch, Norwegisch)

816481

Zoom out

Zoom in

Vorherige Seite

1/98

Nächste Seite

.....wear safety-approved hard hat

......Keep hands clear – pinching hazard.

DANGER! Keep hands away from cutting area and the

blade.

rotating parts - entanglement hazard. Keep

hands, loose clothing and long hair away

from moving parts

do not dispose of electric tools, accessories and

packaging together with household waste material

......warning of general danger

….class II tool

.......read these instructions

......always wear eye protection

......always wear a dust mask.

.....always wear hearing protection

SPECIFIC SAFETY RULES

1. Keep hands away from cutting area and blade at all times! Keep your second hand on an auxiliary

handle. If both hands are holding the saw, they cannot be cut by the blade.

2. Do not reach underneath the work.

3. Hold tool by insulated gripping surfaces when performing an operation where the cutting tools

may contact hidden wiring or its own cord. Contact with a “live” wire will make exposed metal parts of

the tool “live” and shock the operator.

4. Always use blades with correct size and shape arbor holes. Blades that do not match the mounting

hardware of the saw will run eccentrically, causing loss of control.

5. Never use damaged or incorrect arbor flanges or bolts. The arbor flanges and bolt were specially

designed for your saw, for best performance and safety of operation.

6. Maintain a firm grip on the saw and position your body and arm in a way that allows you to resist

KICKBACK forces. KICKBACK forces can be controlled by the operator, if proper precautions are taken.

7. Do not use a dull or damaged blade.

8. Use only recommended blades, rated at the machine’s maximum rated RPM or higher with correct

arbor hole.

9. Tighten blade retaining bolt and all clamps before operating.

10. Check the inside surfaces of the arbor flanges as well as the sides of the blade for freedom from any

foreign matter.

11. Check the blade for cracks or other damage before operation. Replace cracked or damaged blade

immediately. Carry out a test run without load for at least 30 seconds before use.

12. Never start the tool with the workpiece against the blade.

13. Allow the motor to achieve full speed before cutting.

14. Important: After completing the cut, release power switch and wait for coasting blade to stop

completely before putting the saw down

15. Never operate the tool in an area with flammable solids, liquids, or gases. Sparks from the

commutator/carbon brushes could cause a fire or explosion.

16. There are certain applications for which this tool was designed. The manufacturer strongly

recommends that this tool NOT be modified and/or used for any application other than for which

it was designed. If you have any questions relative to its application DO NOT use the tool until you have

written the manufacturer and have been advised.

17. Only use the machine for dry cutting in stone, concrete or masonry.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Carat SL-1255 DUSTEC Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info