Bedienungsanleitung Cardo Scala rider G4 (Seite 12 von 27) (Englisch)

480782

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

There are two ways to search for a new radio station on your G4:

Seek and save:

1. While the Radio is on, select the station number from one to six

that you wish to set by tapping the CHANNEL “B” button until the

desired station is found.

2. Press and hold the Volume Up or Volume Down Button for three

seconds.

• Pressing Volume Up will search upwards (higher frequency).

• Pressing Volume Down will search downwards (lower frequency).

3. Once a station is found, searching stops and you can hear the

station.

4. To continue searching, press the Volume Up or Volume Down Button

again for three seconds.

5. Tap the CHANNEL “B” button within 20 seconds of nding the

station to save the current station.

6. If you don’t save the station, the Radio will exit search mode

without saving the current station. You can still continue to listen

to the current unsaved station. Tapping the CHANNEL “B” Button in

this case will move to the next saved station.

Scan and save:

1. While the Radio is on, select the station number from one to six

that you wish to set by tapping the CHANNEL “B” button until the

desired station is found.

2. Press and hold the Volume Up button for 6 seconds.

3. The device will begin to Scan by searching upwards for the

next station. Once a station is found, searching pauses for a few

seconds while you hear the current station and then the G4 will

automatically continue to the next station.

4. To stop Scanning and stay on the current station, tap the Volume

Up Button again.

5. Tap the CHANNEL “B” button within 20 seconds of nding the

station to save the current station.

6. If you don’t save the station, the Radio will exit search mode

without saving the current station. You can still continue to listen

to the current unsaved station. Tapping the CHANNEL “B” Button in

this case will move to the next saved station.

NOTE: Press CHANNEL “B” button during radio Scan to Fast Save the current

station directly into the Preset Channel number you were last listening to.

Automatic Radio Tuning: Automatically search for and nd 6 new

“on the go” radio stations with one button press.

This feature makes nding new stations fast and easy by creating a

temporary list of “on the go” radio stations.

While the radio is on, press and hold the Volume Down Button for 6

seconds, and the G4 will search upwards from the current frequency

and store the next 6 FM stations it discovers as “on the go” stations.

You can repeat this process as many times as you wish, searching for

the next 6 FM stations each time.

Now you can cycle through these stations by tapping the CHANNEL

“B” button.

NOTE: These 6 temporary “on the go” stations cannot be saved and do not

replace the permanent Saved Radio Stations you may have set using the

“Saving a selected station” procedure. Turning OFF and ON the G4 will clear

out your Automatic Radio Tuning stations, and restore the original saved

radio stations.

scala rider

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Cardo Scala rider G4 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Cardo Scala rider G4

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info