Bedienungsanleitung Carrera Digital 124 - 23613 GENTLEMEN RACE (Seite 12 von 26) (Deutsch, Englisch, Französisch)

550542

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

3 LiPo rechargeable battery for speed controller

1 Transformer

1 Special track

1 Grid Girls

1 Golden plated winners cup

Outside shoulders for curves

Inside shoulders for curves

Shoulder end sections

Guard rails

Track section bolts

Replacement contacts

Instructions

Track length: 39.37 ft./ 12,0 m

Dimensions when assembled: 14.27 x 10.99 ft./ 435 x 335 cm

Important Information

Carrera DIGITAL 124EXCLUSIV

Carrera DIGITAL 124 EXCLUSIV

Please note that Exclusiv (analog system) and Carrera DIGITAL

124/132 (digital system) involve two separate and completely inde-

pendent systems. We hereby expressly indicate that both systems

must be kept separate when setting up the track, i.e. no connecting

rail from Exclusiv may be used together with the connecting rail and

Black Box of the Carrera DIGITAL 124/132, even if only one of the

two connecting rails (Exclusiv connecting rail or Carrera DIGITAL

124/132 connecting rail and Black Box) is attached to the current

supply. Furthermore, no other Carrera DIGITAL 124/132 compo-

nents (switches, electronic lap counter, pit stop) may be built into an

Exclusiv course, i.e. via analog operation.

Non-compliance with the above information may result in damage or

destruction of the respective Carrera DIGITAL 124/132 components.

In this case no warranty may be claimed.

Description

WIRELESS+ is the latest new cordless racetrack delight for Carrera

DIGITAL124 and Carrera DIGITAL 132. The 2.4 GHz radio technolo-

gy with frequency-hopping is free of interference and oﬀers a range

of up to 15 metres. Thanks to powerful lithium polymer rechargeable

battery, continuous play for up to eight hours is possible and stand-

by operation for over 80 days. WIRELESS+ oﬀers cordless freedom

for up to six drivers at the racetrack.

Before first use

Before ﬁrst using the speed controller, the rechargeable battery

supplied

must be inserted in the controller. Unscrew the battery

compartment

on the underside of the speed controller.

Connect the battery plug into the socket in the speed controller and

put the battery in place in the compartment. Finally screw down the

cover of the battery compartment again. The battery is part-loaded

at the factory, but it should be charged completely before being

used for the ﬁrst time.

Care of the battery

To make sure the battery performs well for as long as possible, the

following points should be observed regarding its care and storage.

• Before ﬁrst using them, new batteries should always be charged

fully.

• With a fully-charged battery, continuous play is possible for up

to eight hours. When the battery power is falling oﬀ, range of the

speed controller will diminish. As soon as you notice this, the battery

should be fully recharged.

• If it is not to be used for an extended period, remove the battery

and store the controller at room temperature (16-18 °C) in a dry

place. To prevent a deep discharge of the battery, the stored battery

should be charged every 2 to 3 months.

Assembly instructions

1 4

2 3

Before assembling please insert the connecting clips

in the track as shown in ﬁgure

. Stick tracks together on a ﬂat

base. Move the connecting clips according to ﬁgure

in direction

of the arrow until they audibly snap in. The connecting clip may also

be inserted later. The connecting clips can be removed into both

directions by simply pressing down the clamped nose (see ﬁg.

Fastening: To fasten the track sections on a board, it is neces-

sary to use the track section fasteners (Item no. 85209, not con-

tained in the package).

Note:

Carpeting is not a suitable foundation on which to build the track be-

cause of static charging, formation of ﬂuﬀ and ready inﬂammability.

Guard Rails and Supports

1 2

3 4

Guard rails: Guard rail mounts are ﬁtted by tilting them upwards

onto the verge of the track.

Supporting raised sections: The shank of the ball pivot is

to be inserted into the square slots provided on the underside of the

track. The supports can be made higher by using the extensions.

The pedestal of the supports can be screwed to a base if required

(screws not included).

Supporting steep curves:

Slanting supports of the right height are provided to support steep

curves. Fix the nonadjustable supports at the beginning and end of

the curves. Insert the heads of the supports in the round slots of the

underside of the track.

Electrical connection

Connect the transformer plug with the Control Unit.

Note: To avoid short-circuits and electrocution, the toy may not be

connected using foreign devices, plugs, cables or other objects for-

eign to this toy. The Carrera DIGITAL 124 car racetrack only works

properly with an original Carrera DIGITAL 124 transformer.

The PC interface (PC Unit) may only be operated together with the

original Carrera PC Unit.

Car components

Body

Engine block

Tyres

Rear axle

Rear axle receptacle

including spacer plate

Front axle

Front axle mounting

Board

Central magnet

Rear magnet

Chassis

Rocker arm including spring

Guide keel with double sliding contact

Center magnet retainer

Fastening plate

Note: vehicle construction depends on the model.

The designation of the individual parts may not be used as

order numbers.

Carrera Digital 124 - 23613 GENTLEMEN RACE Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info