Bedienungsanleitung Carrier 38NY009 (Seite 7 von 9) (Englisch)

481299

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

How to remove the drain cap

Clip the drain cap by needle-nose

pliers and pull out.

How to ﬁ x the drain cap

1) Insert hexagon

wrench (4 mm)

in a center head.

4 mm

2) Firmly insert the drain cap.

Do not apply lubricating oil

(refrigerant machine oil) when

inserting the drain cap. Application

causes deterioration and drain

leakage of the plug.

Insert a hexagon

wrench (4 mm).

No gap

Firmly insert the drain hose and drain cap; otherwise, water may leak.

In case of right or left piping

• After scribing slits of the front panel with a

knife or a making-off pin, cut them with a

pair of nippers or an equivalent tool.

In case of bottom right or bottom left piping

• After scribing slits of the front panel with a

knife or a making-off pin, cut them with a

pair of nippers or an equivalent tool.

Slit

Left-hand connection with piping

• Bend the connecting pipe so that it is laid within 43 mm above the wall sur-

face. If the connecting pipe is laid exceeding 43 mm above the wall surface,

the indoor unit may unstably be set on the wall.

When bending the connecting pipe, make sure to use a spring bender so as

not to crush the pipe.

Bend the connecting pipe within a radius of 30 mm.

To connect the pipe after installation of the unit (ﬁ gure)

42NQ009

42NQ012

A 270 270

B 170 230

CAUTION

A mm

B mm

m 3

Liquid side

Gas side

(To the forefront of ﬂ are)

Outward form of indoor unit

R 30 mm (Use polisin (polyethylene)

core or the like for bending pipe.)

Use the handle of screwdriver, etc.

NOTE

If the pipe is bent incorrectly, the indoor unit may unstably be set on the wall.

After passing the connecting pipe through the pipe hole, connect the

connecting pipes to the auxiliary pipes and wrap the facing tape around

them.

• Bind the auxiliary pipes (two) and connecting cable with facing tape

tightly. In case of leftward piping and rear-leftward piping, bind the

auxiliary pipes (two) only with facing tape.

Auxiliary pipes

Indoor unit

Connecting cable

Installation plate

CAUTION

Indoor Unit Fixing

• For detaching the indoor unit from the

installation plate, pull the indoor unit toward

you while pushing its bottom up at the

speciﬁ ed parts.

PushPush

Press

(unhook)

Hook

Hook here.

Installation plate

1. Pass the pipe through the hole in the wall and hook the indoor unit on the

installation plate at the upper hook.

2. Swing the indoor unit to right and left to conﬁ rm that it is ﬁ rmly hooked up on

the installation plate.

3. While pressing the indoor unit onto the wall, hook it at the lower part on the

installation plate. Pull the indoor unit toward you to conﬁ rm that it is ﬁ rmly

hooked up on the installation plate.

Drainage

1. Run the drain hose sloped downwards.

2. Put water in the drain pan and make sure that the water is drained out of

doors.

3. When connecting extension drain hose, insulate the connecting part of

extension drain hose with shield pipe.

NOTE

• The hole should be made at a slight downward slant on the outdoor side.

50 mm

or more

Do not put the

drain hose end

into water.

Do not put the

drain hose end

in the drainage ditch.

Do not form the

drain hose into

a wavy shape.

Do not rise the

drain hose.

Extension drain hose

Inside the room

Drain hose

Shield pipe

Arrange the drain pipe for proper drainage from the unit.

Improper drainage can result in dew-dropping.

CAUTION

• Carefully arrange pipes so that any pipe does not stick out of the rear

plate of the indoor unit.

• Carefully connect the auxiliary pipes and connecting pipes to one

another and cut off the insulating tape wound on the connecting pipe to

avoid double-taping at the joint; moreover, seal the joint with the vinyl

tape, etc.

• Since dewing results in a machine trouble, make sure to insulate both

connecting pipes. (Use polyethylene foam as insulating material.)

• When bending a pipe, carefully do it, not to crush it.

Wall

Drain

guide

Space for pipes

This air conditioner has the structure designed

to drain water collected from dew, which forms

on the back of the indoor unit, to the drain pan.

Therefore, do not store the power cord and other

parts at a height above the drain guide.

1110251161-EN.indd 51110251161-EN.indd 5 12/28/07 6:10:52 PM12/28/07 6:10:52 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Carrier 38NY009 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Carrier 38NY009

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info