Bedienungsanleitung Casio 3185 - GF-1000 (Seite 5 von 8) (Englisch)

624494

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

Operation Guide 3185

E-40

Alarm Operation

The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the

watch is in. In the case of the snooze alarm, the alarm operation is performed a total

of seven times, every five minutes, until you turn the alarm off (page E-41).

• Alarm and Hourly Time Signal operations are performed in accordance with the

Timekeeping Mode time.

• To stop the alarm tone after it starts to sound, press any button.

• Performing any one of the operations below during a 5-minute interval between

snooze alarms cancels the current snooze alarm operation.

Displaying the Timekeeping Mode setting screen (page E-13)

Displaying the

SNZ

setting screen (page E-39)

To test the alarm

In the Alarm Mode, hold down D to sound the alarm.

E-41

To turn an alarm on and off

1. In the Alarm Mode, use D to select an alarm.

2. Press A to toggle it on (

) and off (xx).

• Turning on an alarm (

AL1, AL2, AL3, AL4 or

SNZ) displays the alarm on indicator on its Alarm Mode

screen.

• In all modes, the alarm on indicator is shown for any

alarm that currently is turned on.

• The alarm on indicator flashes while the alarm is

sounding.

• The snooze alarm indicator (SNZ) flashes while the

snooze alarm is sounding and during the 5-minute

intervals between alarms.

Alarm on indicator

On/Off status

E-42

To turn the Hourly Time Signal on and off

1. In the Alarm Mode, use D to select the Hourly Time

Signal (

SIG).

2. Press A to toggle it on (

) and off (xx).

• The Hourly Time Signal on indicator is shown on the

display in all modes while this function is turned on.

Hourly time signal

on indicator

On/Off status

E-43

Stopwatch

The stopwatch lets you measure elapsed time, split times,

and two finishes.

• The display range of the stopwatch is 23 hours, 59

minutes, 59.99 seconds.

• The stopwatch continues to run, restarting from zero

after it reaches its limit, until you stop it.

• The stopwatch measurement operation continues even

if you exit the Stopwatch Mode.

• Exiting the Stopwatch Mode while a split time is frozen

on the display clears the split time and returns to

elapsed time measurement.

• All of the operations in this section are performed in the

Stopwatch Mode, which you enter by pressing C (page

E-11).

1/100 second

Hours

Seconds

Minutes

E-44

To measure times with the stopwatch

Elapsed Time

Split Time

Two Finishes

Start

Stop Re-start Stop

Split

(SPL displayed)

Split release Stop

Split

First runner finishes.

Display time of first

runner.

Stop

Second runner

finishes.

Split release

Display time of

second runner.

➤➤➤

➤

Clear

E-45

Countdown Timer

You can set the countdown timer within a range of one

minute to 24 hours. An alarm sounds when the countdown

reaches zero.

• All of the operations in this section are performed in the

Countdown Timer Mode, which you enter by pressing

C (page E-11).

Countdown End Beeper

The countdown end beeper lets you know when the

countdown reaches zero. The beeper stops after about 10

seconds or when you press any button.

Minutes

Seconds

Hours

E-46

To configure the countdown timer

1. While the countdown start time is on the display in the

Countdown Timer Mode, hold down A until the current

countdown start time starts to flash, which indicates the

setting screen.

• If the countdown start time is not displayed, use the

procedure under “To use the countdown timer” (page

E-47) to display it.

2. Press C to move the flashing between the hour and

minute settings.

3. When a setting is flashing, use D (+) and B (–) to

change it.

• To specify a countdown start time of 24 hours, set

4. Press A to exit the setting screen.

E-47

To use the countdown timer

Press D while in the Countdown Timer Mode to start the

countdown timer.

• The countdown timer operation continues even if you

exit the Countdown Timer Mode.

• Press D while a countdown operation is in progress to

pause it. Press D again to resume the countdown.

• To stop a countdown operation completely, first pause it

(by pressing D), and then press A. This returns the

countdown time to its starting value.

Current timer time

Timer start time

E-48

Illumination

This watch has an EL (electro-luminescent) panel that

causes the entire display to glow for easy reading in the

dark. The watch’s auto light switch turns on illumination

automatically when you angle the watch towards your

face.

• The auto light switch must be turned on (indicated by

the auto light switch on indicator) for it to operate.

• See “Illumination Precautions” (page E-70) for other

important information about using illumination.

To illuminate the display manually

In any mode, press B to turn on illumination.

• The above operation turns on illumination regardless of

the current auto light switch setting.

Auto light switch on

indicator

E-49

• You can use the procedure below to select either 1.5 seconds or 3 seconds as the

illumination duration when you press B.

• Regardless of the watch’s current illumination duration setting, the display remains

illuminated for about three seconds in the Diving Mode.

To specify the illumination duration

1. In the Timekeeping Mode, hold down A until the

display contents start to flash. This is the setting screen.

2. Press C 10 times until the current illumination duration

setting (

or ) appears.

3. Press D to toggle the setting between

(approximately 1.5 seconds) and (approximately

3 seconds).

4. Press A to exit the setting screen.

Casio 3185 - GF-1000 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info